3Com 10002211 manual User, Documentation

Page 14

8COREBUILDER 6000 EXTENDED SWITCHING SOFTWARE REVISION 8.2.3

	After the software is loaded, this message appears:
	Installation complete.
	If the CoreBuilder executable software image stored in ﬂash memory is
	corrupted (for example, when the power fails while you are updating
	software), contact 3Com Technical Support. See Appendix E.
6	To reboot the system to use the newly loaded software, enter:
	system reboot
	You are prompted with the following message:
	Are you sure you want to reboot the system (n/y) [y]:
7	At the prompt, enter y (for Yes).
	You are now ready to conﬁgure management access for your system. See
	the CoreBuilder 6000 Getting Started Guide.

User	This version of software is compatible with the documentation listed here.
Documentation	Some of this documentation may be available on CD-ROM. These release
	notes describe any changes and additions to this documentation.
■	CoreBuilder 6000 Getting Started Guide
■	CoreBuilder 6000 Control Panel User Guide
■	CoreBuilder 6000 Operation Guide
■	Corebuilder 6000 Administration Console User Guide
■	CoreBuilder 6000 Command Quick Reference (folded card)
■	LANplex 6000 Extended Switching User Guide
	The Extended Switching User Guide is shipped with Extended Switching
	software.
	Individual modules are shipped with their installation guides:
■	LMM+ (LANswitching Management Module +) Installation Guide
■	FCM (FDDI Concentrator Module) Installation Guide
■	EFSM (Ethernet/FDDI Switching Module) Installation Guide
■	TRSM (Token Ring Switching Module) Installation Guide
■	TMM Fast Ethernet (Tri-Media Module) Installation Guide

Image 14

Contents CoreBuilder Extended Switching Software Revision October 17 CorebuilderUnited States Government Legends Contents IP Multicast Routing Vlans on the Corebuilder System 3COM Corporation Limited Warranty Dated May 30 CoreBuilder 6000 Extended Switching software from 3ComOverview Corebuilder 6000 Extended Switching Software Revision Updating Your System Software Remove diskette #3 using the following command Remove diskette #1 using the following commandRemove diskette #2 using the following command Following ﬁles are now in your /usr/lp6000R directory Remove diskette #4 using the following commandRemove diskette #5 using the following command LMM+ Loading SystemSoftware on \3com\lp6000R\image\lp6000R User DocumentationCorrections implemented at this release What’s New atRevision 8.2.3? To deﬁne an IP interface Enter the number of the Vlan whose interface you are deﬁning AxFDDI axFDDI group AxFDDIHistory axFDDI groupDisplaying Bridge Information To enable Spanning Tree transitions, enterTo disable Spanning Tree transitions, enter System prompts you for slot numbersSample display of bridge port information Revision 8.2.0? Corrections that are implemented at this releaseWhat’s New at Revision 8.2.0? You receive the prompt to select each port’s duplex mode System displays this messageDefault To select the default all, press Return FTP Packet Filter Program Transfers via Snmp ﬁrst telnet session is disconnected and the system displays Sample screen showing the display after the changes What’s New at Revision 8.2.0? Power supply +5-volt input is restored Power supply +5-volt input has failedPower supply +12-volt input has failed This message is immediately overwritten withSystem Issues System nvdata reset System Issues Known Problems New Imports section now looks like thisReceived ftpCommand Quit not completed errno Corebuilder 6000 Extended Switching Software Revision Snmp MIB Files Support for IP routing on the Fddi Switching Module FSM Configurable Source Route hop count limit Efsm LpBridgePortAddressLearnedEvent Corebuilder 6000 Extended Switching Software Revision IP Multicast Routing Following parametersDisabling Igmp EnablingDisabling Dvmrp Interfaces Administering IPMulticast Multicast interface Example multicast interface conﬁguration for the slotDisabling Multicast Interfaces Enabling Multicast InterfacesExample AdministeringMulticast Tunnels Address of the remote multicast routerEnter the Dvmrp metric value of the tunnel Associate a multicast tunnelEnter the IP address of the destination multicast router Enter the Time To Live TTL threshold of the tunnelDisplaying Routes Following display shows all available multicast routes Table A-1describes the ﬁelds in the route displayDisplaying Multicast CacheFollowing display shows the multicast cache conﬁguration Table A-2describes the ﬁelds in the CacheDisplay Remote Monitoring Rmon B Technology CoreBuilder ImplementationSegment being monitored Table B-3 Supported Ethernet and Fddi Frame Size Buckets Rmon Groups Setting Alarm Thresholds Example of an Alarm ThresholdRmon Groups 3Com Transcend Rmon Agents Management Information Base MIB Figure B-3 Example of an Rmon MIB Counter Object Create ﬁrewalls About VLANsCoreBuilder system, VLANs allow you to LocationsAppendix C Vlans on the Corebuilder System Protocol Suite Layer 3 Addressing Information SNAModifying the Default Vlan How CoreBuilder System Makes Flooding DecisionsVlan Exception Flooding Overlapped IP VLANs Routing Between VLANs Administering Vlans Displaying Vlan InformationExample of a summary display for several VLANs Table D-1describes these statistics Traditional Bridge Deﬁning VlanInformation for a As an Efsm or a TMMDeﬁning Vlan Follow these steps to create a Vlan deﬁnition Information for An HSI Switch EngineEnter the subnetwork mask Enter the IP subnet address Enter the subnetwork mask Bridge vlan modify Bridge vlan remove Technical Support Access by Analog Modem Type go threecom Regional Sales Office Telephone Number 3Com Corporation Returning Products for Repair Page 3Com Corporation Limited Warranty Limitation of Liability