3Com 10002211 manual Associate a multicast tunnel, Enter the Dvmrp metric value of the tunnel

Page 47

Administering Multicast Tunnels

A-7

Defining a To define a multicast tunnel:

Multicast Tunnel

1 From the top level of the Administration Console, enter:

Top-Level Menu

 

 

 

ip multicast tunnel define

system

interface

 

 

 

 

 

 

 

ethernet

route

dvmrp

display

2

Enter the slot(s) of the switching module for which you want to define a

fddi

arp

igmp

 

 

 

 

 

tokenring

multicast

interface define

 

multicast tunnel.

bridge

 

ip

udpHelpertunnel

remove

 

 

routing

routeDisplay

 

 

ipx

 

 

 

cacheDisplay

3

Enter the index number(s) of the interface(s) with which you want to

appletalk

 

rip

 

 

snmp

ping

 

 

 

associate a multicast tunnel.

analyzer

statistics

 

 

 

 

 

 

 

script

 

 

 

 

 

logout

 

 

 

4

Enter the IP address of the destination multicast router.

 

 

 

 

 

 

 

 

 

The IP address of the destination multicast router must be a remote address.

 

 

 

 

 

The destination router cannot be directly connected to the same

 

 

 

 

 

subnetworks as the local IP address.

 

 

 

 

5

Enter the DVMRP metric value of the tunnel.

 

 

 

 

6

Enter the Time To Live (TTL) threshold of the tunnel.

 

 

 

 

7

Enter the rate limit of the tunnel.

 

 

 

 

 

Example:

 

 

 

 

 

Select IP stack by slot {2,3,7,9-12all} [9]:

 

 

 

 

 

Enter an IP interface index [1]: 2

 

 

 

 

 

Enter remote IP address: 192.9.200.40

 

 

 

 

 

Enter tunnel DVMRP metric [1]: 1

 

 

 

 

 

Enter tunnel TTL threshold [1]:

 

 

 

 

 

Enter tunnel rate limit [0]:

Image 47
Contents Corebuilder CoreBuilder Extended Switching Software Revision October 17United States Government Legends Contents IP Multicast Routing Vlans on the Corebuilder System 3COM Corporation Limited Warranty Dated May 30 CoreBuilder 6000 Extended Switching software from 3ComOverview Corebuilder 6000 Extended Switching Software Revision Updating Your System Software Remove diskette #3 using the following command Remove diskette #1 using the following commandRemove diskette #2 using the following command Following files are now in your /usr/lp6000R directory Remove diskette #4 using the following commandRemove diskette #5 using the following command LMM+ Loading SystemSoftware on \3com\lp6000R\image\lp6000R Documentation UserCorrections implemented at this release What’s New atRevision 8.2.3? To define an IP interface AxFDDI axFDDI group AxFDDIHistory axFDDI group Enter the number of the Vlan whose interface you are definingSystem prompts you for slot numbers To enable Spanning Tree transitions, enterTo disable Spanning Tree transitions, enter Displaying Bridge InformationSample display of bridge port information Corrections that are implemented at this release Revision 8.2.0?What’s New at Revision 8.2.0? System displays this message You receive the prompt to select each port’s duplex modeDefault To select the default all, press Return FTP Packet Filter Program Transfers via Snmp first telnet session is disconnected and the system displays Sample screen showing the display after the changes What’s New at Revision 8.2.0? This message is immediately overwritten with Power supply +5-volt input has failedPower supply +12-volt input has failed Power supply +5-volt input is restoredSystem Issues System nvdata reset System Issues New Imports section now looks like this Known ProblemsReceived ftpCommand Quit not completed errno Corebuilder 6000 Extended Switching Software Revision Snmp MIB Files Support for IP routing on the Fddi Switching Module FSM Configurable Source Route hop count limit Efsm LpBridgePortAddressLearnedEvent Corebuilder 6000 Extended Switching Software Revision Following parameters IP Multicast RoutingDisabling Igmp EnablingDisabling Dvmrp Interfaces Administering IPMulticast Example multicast interface configuration for the slot Multicast interfaceEnabling Multicast Interfaces Disabling Multicast InterfacesAddress of the remote multicast router AdministeringMulticast Tunnels ExampleEnter the Time To Live TTL threshold of the tunnel Associate a multicast tunnelEnter the IP address of the destination multicast router Enter the Dvmrp metric value of the tunnelDisplaying Routes Table A-1describes the fields in the route display Following display shows all available multicast routesMulticast Cache DisplayingFollowing display shows the multicast cache configuration Table A-2describes the fields in the CacheDisplay Remote Monitoring Rmon B Technology Implementation CoreBuilderSegment being monitored Table B-3 Supported Ethernet and Fddi Frame Size Buckets Rmon Groups Example of an Alarm Threshold Setting Alarm ThresholdsRmon Groups 3Com Transcend Rmon Agents Management Information Base MIB Figure B-3 Example of an Rmon MIB Counter Object Locations About VLANsCoreBuilder system, VLANs allow you to Create firewallsAppendix C Vlans on the Corebuilder System Protocol Suite SNA Layer 3 Addressing InformationHow CoreBuilder System Makes Flooding Decisions Modifying the Default VlanVlan Exception Flooding Overlapped IP VLANs Routing Between VLANs Displaying Vlan Information Administering VlansExample of a summary display for several VLANs Table D-1describes these statistics As an Efsm or a TMM Defining VlanInformation for a Traditional BridgeDefining Vlan Follow these steps to create a Vlan definition Information for An HSI Switch EngineEnter the subnetwork mask Enter the IP subnet address Enter the subnetwork mask Bridge vlan modify Bridge vlan remove Technical Support Access by Analog Modem Type go threecom Regional Sales Office Telephone Number 3Com Corporation Returning Products for Repair Page 3Com Corporation Limited Warranty Limitation of Liability