3Com 10002211 manual Bridge vlan remove

Page 78

D-8 APPENDIX D: ADMINISTERING VLANS

Removing VLAN Follow these steps to remove a VLAN deﬁnition: Information

1 From the top level of the Administration Console, enter:

Top-Level Menu

	system
	ethernet
	fddi	display
	tokenring	mode
	➧bridge	lowLatency
	ip	ipFragmentation
	ipx	ipxSnapTranslation
	appletalk	trFDDIMode
	snmp	addressThreshold
	analyzer	agingTime	summary
	script	stpState	summary
	script	stpState	detail
	logout	stpPriority	detail
	logout	stpPriority	define
		stpMaxAge	define
		stpMaxAge	modify
		stpHelloTIme	modify
		stpHelloTIme	➧remove
		stpForwardDelay	➧remove
		stpGroupAddress
		srBridgeNumber
		port
		packetFilter
		➧vlan

bridge vlan remove

2Enter the slot number for the bridge.

3Enter the indexes for the VLANs you want to remove.

Example:

Select menu option (bridge/vlan): remove

Select bridge(s) by slot (2-3,5,10-12all) [10]:10

Select VLAN index(es) (1-2all): 1

Image 78

Contents CoreBuilder Extended Switching Software Revision October 17 CorebuilderUnited States Government Legends Contents IP Multicast Routing Vlans on the Corebuilder System 3COM Corporation Limited Warranty CoreBuilder 6000 Extended Switching software from 3Com OverviewDated May 30 Corebuilder 6000 Extended Switching Software Revision Updating Your System Software Remove diskette #1 using the following command Remove diskette #2 using the following commandRemove diskette #3 using the following command Remove diskette #4 using the following command Remove diskette #5 using the following commandFollowing ﬁles are now in your /usr/lp6000R directory Loading System Software onLMM+ \3com\lp6000R\image\lp6000R User DocumentationWhat’s New at Revision 8.2.3?Corrections implemented at this release To deﬁne an IP interface Enter the number of the Vlan whose interface you are deﬁning AxFDDI axFDDI group AxFDDIHistory axFDDI groupDisplaying Bridge Information To enable Spanning Tree transitions, enterTo disable Spanning Tree transitions, enter System prompts you for slot numbersSample display of bridge port information Revision 8.2.0? Corrections that are implemented at this releaseWhat’s New at Revision 8.2.0? You receive the prompt to select each port’s duplex mode System displays this messageDefault To select the default all, press Return FTP Packet Filter Program Transfers via Snmp ﬁrst telnet session is disconnected and the system displays Sample screen showing the display after the changes What’s New at Revision 8.2.0? Power supply +5-volt input is restored Power supply +5-volt input has failedPower supply +12-volt input has failed This message is immediately overwritten withSystem Issues System nvdata reset System Issues Known Problems New Imports section now looks like thisReceived ftpCommand Quit not completed errno Corebuilder 6000 Extended Switching Software Revision Snmp MIB Files Support for IP routing on the Fddi Switching Module FSM Configurable Source Route hop count limit Efsm LpBridgePortAddressLearnedEvent Corebuilder 6000 Extended Switching Software Revision IP Multicast Routing Following parametersEnabling Disabling DvmrpDisabling Igmp Administering IP MulticastInterfaces Multicast interface Example multicast interface conﬁguration for the slotDisabling Multicast Interfaces Enabling Multicast InterfacesExample AdministeringMulticast Tunnels Address of the remote multicast routerEnter the Dvmrp metric value of the tunnel Associate a multicast tunnelEnter the IP address of the destination multicast router Enter the Time To Live TTL threshold of the tunnelDisplaying Routes Following display shows all available multicast routes Table A-1describes the ﬁelds in the route displayDisplaying Multicast CacheFollowing display shows the multicast cache conﬁguration Table A-2describes the ﬁelds in the CacheDisplay Remote Monitoring Rmon B Technology CoreBuilder ImplementationSegment being monitored Table B-3 Supported Ethernet and Fddi Frame Size Buckets Rmon Groups Setting Alarm Thresholds Example of an Alarm ThresholdRmon Groups 3Com Transcend Rmon Agents Management Information Base MIB Figure B-3 Example of an Rmon MIB Counter Object Create ﬁrewalls About VLANsCoreBuilder system, VLANs allow you to LocationsAppendix C Vlans on the Corebuilder System Protocol Suite Layer 3 Addressing Information SNAModifying the Default Vlan How CoreBuilder System Makes Flooding DecisionsVlan Exception Flooding Overlapped IP VLANs Routing Between VLANs Administering Vlans Displaying Vlan InformationExample of a summary display for several VLANs Table D-1describes these statistics Traditional Bridge Deﬁning VlanInformation for a As an Efsm or a TMMInformation for An HSI Switch Engine Enter the subnetwork maskDeﬁning Vlan Follow these steps to create a Vlan deﬁnition Enter the IP subnet address Enter the subnetwork mask Bridge vlan modify Bridge vlan remove Technical Support Access by Analog Modem Type go threecom Regional Sales Office Telephone Number 3Com Corporation Returning Products for Repair Page 3Com Corporation Limited Warranty Limitation of Liability