3Com 10002211 manual What’s New at Revision 8.2.0?

Page 27

What’s New at Revision 8.2.0?

21

Note these additional items:

The linkState up or down settings apply to Ethernet and Fast Ethernet ports, not to FDDI ports, and only when the stpState for the bridge is enabled. If the stpState on the Bridge menu is disabled, the State for the port remains in forwarding state.

When the bridge port is in the Removed state, the State remains in forwarding state.

If STP is disabled on an individual port, the State remains disabled.

Table 1 describes the port states and how they relate to the linkState. This table is valid only when the stpState for the bridge is enabled.

Table 1 Port States When stpState Is Enabled

If STP is

and linkState is

Then Port State is

 

 

 

enabled

up

blocking or forwarding*

enabled

down

disabled

disabled

up

disabled

disabled

down

disabled

removed

up

forwarding

removed

down

forwarding

*The Port State is either blocking or forwarding. The final state depends on the Spanning Tree configuration of the network.

CoreBuilder 6000 12-Slot Chassis

The CoreBuilder 6000 12-slot chassis is the latest generation of the CoreBuilder 6000 chassis. This chassis and the 8.2.3 software release allow you to remove and replace the power supplies and fan trays in case of failure.

Hot-swappable Power Supplies. The LED on each power supply lights green when the power supply is running correctly. If the power supply fails, the system generates a sound and the power supply LED does not light. You can remove and replace either of the two power supplies at the back of the chassis. (Turning off one of the power supplies generates a sound, and the control panel LCD displays Input Failure.)

Image 27
Contents Corebuilder CoreBuilder Extended Switching Software Revision October 17United States Government Legends Contents IP Multicast Routing Vlans on the Corebuilder System 3COM Corporation Limited Warranty CoreBuilder 6000 Extended Switching software from 3Com OverviewDated May 30 Corebuilder 6000 Extended Switching Software Revision Updating Your System Software Remove diskette #1 using the following command Remove diskette #2 using the following commandRemove diskette #3 using the following command Remove diskette #4 using the following command Remove diskette #5 using the following commandFollowing files are now in your /usr/lp6000R directory Loading System Software onLMM+ \3com\lp6000R\image\lp6000R Documentation UserWhat’s New at Revision 8.2.3?Corrections implemented at this release To define an IP interface AxFDDI axFDDI group AxFDDIHistory axFDDI group Enter the number of the Vlan whose interface you are definingSystem prompts you for slot numbers To enable Spanning Tree transitions, enterTo disable Spanning Tree transitions, enter Displaying Bridge InformationSample display of bridge port information Corrections that are implemented at this release Revision 8.2.0?What’s New at Revision 8.2.0? System displays this message You receive the prompt to select each port’s duplex modeDefault To select the default all, press Return FTP Packet Filter Program Transfers via Snmp first telnet session is disconnected and the system displays Sample screen showing the display after the changes What’s New at Revision 8.2.0? This message is immediately overwritten with Power supply +5-volt input has failedPower supply +12-volt input has failed Power supply +5-volt input is restoredSystem Issues System nvdata reset System Issues New Imports section now looks like this Known ProblemsReceived ftpCommand Quit not completed errno Corebuilder 6000 Extended Switching Software Revision Snmp MIB Files Support for IP routing on the Fddi Switching Module FSM Configurable Source Route hop count limit Efsm LpBridgePortAddressLearnedEvent Corebuilder 6000 Extended Switching Software Revision Following parameters IP Multicast RoutingEnabling Disabling DvmrpDisabling Igmp Administering IP MulticastInterfaces Example multicast interface configuration for the slot Multicast interfaceEnabling Multicast Interfaces Disabling Multicast InterfacesAddress of the remote multicast router AdministeringMulticast Tunnels ExampleEnter the Time To Live TTL threshold of the tunnel Associate a multicast tunnelEnter the IP address of the destination multicast router Enter the Dvmrp metric value of the tunnelDisplaying Routes Table A-1describes the fields in the route display Following display shows all available multicast routesMulticast Cache DisplayingFollowing display shows the multicast cache configuration Table A-2describes the fields in the CacheDisplay Remote Monitoring Rmon B Technology Implementation CoreBuilderSegment being monitored Table B-3 Supported Ethernet and Fddi Frame Size Buckets Rmon Groups Example of an Alarm Threshold Setting Alarm ThresholdsRmon Groups 3Com Transcend Rmon Agents Management Information Base MIB Figure B-3 Example of an Rmon MIB Counter Object Locations About VLANsCoreBuilder system, VLANs allow you to Create firewallsAppendix C Vlans on the Corebuilder System Protocol Suite SNA Layer 3 Addressing InformationHow CoreBuilder System Makes Flooding Decisions Modifying the Default VlanVlan Exception Flooding Overlapped IP VLANs Routing Between VLANs Displaying Vlan Information Administering VlansExample of a summary display for several VLANs Table D-1describes these statistics As an Efsm or a TMM Defining VlanInformation for a Traditional BridgeInformation for An HSI Switch Engine Enter the subnetwork maskDefining Vlan Follow these steps to create a Vlan definition Enter the IP subnet address Enter the subnetwork mask Bridge vlan modify Bridge vlan remove Technical Support Access by Analog Modem Type go threecom Regional Sales Office Telephone Number 3Com Corporation Returning Products for Repair Page 3Com Corporation Limited Warranty Limitation of Liability