3Com 10002211 manual Displaying, Multicast Cache

Page 50

A-10 APPENDIX A: IP MULTICAST ROUTING

Displaying the

 

 

The multicast cache contains the IP source address and destination address

Multicast Cache

 

 

for packets observed on the system. The multicast cache shows you how

 

 

 

 

 

 

 

information is routed over interfaces and ports in your system.

 

 

 

 

 

 

 

To display all learned routes in the multicast cache:

Top-Level Menu

 

 

1

From the top level of the Administration Console, enter:

system

 

 

 

 

 

 

 

interface

 

 

 

 

ip multicast cacheDisplay

ethernet

 

 

 

 

route

dvmrp

 

 

fddi

 

 

 

arp

igmp

 

 

 

tokenring

 

 

 

multicast

interfaces

 

2

Enter the slot(s) of the switching module for which you want to view the

bridge

 

udpHelper

tunnel

 

ip

 

 

 

multicast cache.

routeDisplay

 

 

ipx

routing

 

 

icmpRouterDis

 

 

 

appletalk

cacheDisplayovery

 

 

 

rip

 

 

 

 

 

snmp

 

 

3 Enter the multicast source address at the prompt.

ping

 

 

analyzer

 

 

script

statistics

 

 

 

 

 

 

 

 

 

 

 

 

logout

 

 

 

 

4 Enter the multicast group address at the prompt.

 

 

 

 

 

 

 

 

 

 

 

 

The DVMRP status and IGMP status appear on the screen.

 

 

 

 

 

 

 

Example:

 

 

 

 

 

 

 

Select IP stack(s) by slot (2,3,7,9-12all) [12]:

 

 

 

 

 

 

 

Enter multicast source address [131.188.0.0]

 

 

 

 

 

 

 

Enter multicast group address [244.2.0.2]

 

 

 

 

 

 

 

DVMRP is enabled, IGMP snooping is enabled

Image 50
Contents CoreBuilder Extended Switching Software Revision October 17 CorebuilderUnited States Government Legends Contents IP Multicast Routing Vlans on the Corebuilder System 3COM Corporation Limited Warranty Dated May 30 CoreBuilder 6000 Extended Switching software from 3ComOverview Corebuilder 6000 Extended Switching Software Revision Updating Your System Software Remove diskette #3 using the following command Remove diskette #1 using the following commandRemove diskette #2 using the following command Following files are now in your /usr/lp6000R directory Remove diskette #4 using the following commandRemove diskette #5 using the following command LMM+ Loading SystemSoftware on \3com\lp6000R\image\lp6000R User DocumentationCorrections implemented at this release What’s New atRevision 8.2.3? To define an IP interface Enter the number of the Vlan whose interface you are defining AxFDDI axFDDI group AxFDDIHistory axFDDI groupDisplaying Bridge Information To enable Spanning Tree transitions, enterTo disable Spanning Tree transitions, enter System prompts you for slot numbersSample display of bridge port information Revision 8.2.0? Corrections that are implemented at this releaseWhat’s New at Revision 8.2.0? You receive the prompt to select each port’s duplex mode System displays this messageDefault To select the default all, press Return FTP Packet Filter Program Transfers via Snmp first telnet session is disconnected and the system displays Sample screen showing the display after the changes What’s New at Revision 8.2.0? Power supply +5-volt input is restored Power supply +5-volt input has failedPower supply +12-volt input has failed This message is immediately overwritten withSystem Issues System nvdata reset System Issues Known Problems New Imports section now looks like thisReceived ftpCommand Quit not completed errno Corebuilder 6000 Extended Switching Software Revision Snmp MIB Files Support for IP routing on the Fddi Switching Module FSM Configurable Source Route hop count limit Efsm LpBridgePortAddressLearnedEvent Corebuilder 6000 Extended Switching Software Revision IP Multicast Routing Following parametersDisabling Igmp EnablingDisabling Dvmrp Interfaces Administering IPMulticast Multicast interface Example multicast interface configuration for the slotDisabling Multicast Interfaces Enabling Multicast InterfacesExample AdministeringMulticast Tunnels Address of the remote multicast routerEnter the Dvmrp metric value of the tunnel Associate a multicast tunnelEnter the IP address of the destination multicast router Enter the Time To Live TTL threshold of the tunnelDisplaying Routes Following display shows all available multicast routes Table A-1describes the fields in the route displayDisplaying Multicast CacheFollowing display shows the multicast cache configuration Table A-2describes the fields in the CacheDisplay Remote Monitoring Rmon B Technology CoreBuilder ImplementationSegment being monitored Table B-3 Supported Ethernet and Fddi Frame Size Buckets Rmon Groups Setting Alarm Thresholds Example of an Alarm ThresholdRmon Groups 3Com Transcend Rmon Agents Management Information Base MIB Figure B-3 Example of an Rmon MIB Counter Object Create firewalls About VLANsCoreBuilder system, VLANs allow you to LocationsAppendix C Vlans on the Corebuilder System Protocol Suite Layer 3 Addressing Information SNAModifying the Default Vlan How CoreBuilder System Makes Flooding DecisionsVlan Exception Flooding Overlapped IP VLANs Routing Between VLANs Administering Vlans Displaying Vlan InformationExample of a summary display for several VLANs Table D-1describes these statistics Traditional Bridge Defining VlanInformation for a As an Efsm or a TMMDefining Vlan Follow these steps to create a Vlan definition Information for An HSI Switch EngineEnter the subnetwork mask Enter the IP subnet address Enter the subnetwork mask Bridge vlan modify Bridge vlan remove Technical Support Access by Analog Modem Type go threecom Regional Sales Office Telephone Number 3Com Corporation Returning Products for Repair Page 3Com Corporation Limited Warranty Limitation of Liability