Panduit LS7 manual Print Head & Rollers, To clean the print head and rollers

Page 16

PRINT HEAD & ROLLERS

Occasionally, specks of dust or dirt become attached to the machine’s print head and rollers. This is particularly likely when you are using the unit outdoors or in a very dus ty environment. If a section of the print head is covered with dust, a blank horizontal streak may appear through the label text. Therefore, the machine’s head may need to be cleaned from time to time.

To clean the print head and rollers:

1Turn off the machine.

2Remove the back cover, and then remove the tape cassette if one is installed. The print head and rollers are located in the tape compartment .

3Print head: Use a dry cotton swab to gently wipe the print head with an up-and-down motion.

Rollers: Us e a dry cotton swab to wipe each roller with an up-and-down motion while rotating them with your finger.

4Install a tape cassette, attach the back cover, and then try printing again.

5If dus t still remains, use Panduit Cleaning Cassette (LS7-CLN).

If none of the above works, contact Technical Support at 866-871-4571.

13

Image 16

Contents Page Contents Page Getting started Introduction and Safe Operation Safe Operation PracticesDo Not Operate In An Explosive Environment Do Not Operate In Wet Or Damp AreasInformation to USA Users Information to Canadian Users General Precautions Warranty Information TOP View General DescriptionBottom View Keyboard & LCD Display LS7Batteries To change the batteriesOptional AC Adapter To connect the optional AC adapterTape Cassette To change the LS7 tape cassetteLabel Code Label CodeTape Width Laminated Industrial Tape Separator Tool Laminated Industrial TapeTo clean the print head and rollers Print Head & RollersPrint head Rollers Tape Cutter To clean the tape cutter bladesBe careful not to touch the cutter blades with bare hands Carrying Case For your Information To turn on the machine Power KEYTo turn off the machine Code & Caps Keys Code KEYCaps KEY To type capital letters continuous lyLeft Cursor KEY Cursor KeysRight Cursor KEY UP Cursor KEY Down Cursor KEYSpace KEY To add a spaceReturn KEY Is used to end a1John Smith To add a new line of text1DATA To apply a selected itemTo delete one character Backspace KEYTo delete a sequence of characters To quit a function without changing your text Clear Function To delete all of the textAccented characters Accent FunctionTo type in an accented character Èéëêe Accent1NOË Symbols Symbol FunctionTo type in a symbol 1PHONE To turn on or off the length function Length FunctionTo set the length of the label Length inch LengthSize Function Setting Size PointsTape width Sizes in points To change the size setting SizeAuto Tape Width Text 12 mmWhile still holding down Code , con To change the underline setting Underline FunctionUnderline OFFRound Slant DOT Frame FunctionTo change the frame s etting Frame DOTHorizontal Alignment Function Left Center RightAlignment LeftMirror Printing Function To change the mirror printing settingMirror Print KEY, Copies & Feed Functions CopiesSerialization Function To use the numbering functionSerialize NumericStart Value END ValueTo enable the rotate legend function Rotate Legend FunctionIncrement Repeat Legnd Repeat Legend FunctionRotate Legnd 01.00 To enable/dis able the line function Line Drawing FunctionVertcl Line Right EdgePress Increment byTo enable the page function FunctionLabel 1A207Storing Text Memory File FunctionsTo store a text file Recalling Text Deleting a FileTo overwrite the stored file with the new one To recall a text fileFile Store Press Or pres s just BS Press the keyFile RecallFile Clear Barcode Function To change the barcode parameter settings Symbol CharacterTo add a special character to the barcode data To add the barcode to your textTo delete the barcode from your text Code Width SmallCheck DIG OFF Check DIGCode Problem Remedy TroubleshootingLabel Code Error Message List Buffer Empt YFUL L CAN’TProblem FunctionNot Allowed InvalidError SE TLengt H SystemTechnical Support Contacts HardwareSoftware LCD