SUPER MICRO Computer X9DRG-HTF, X9DRG-HF user manual Bios Error Beep Codes, X9 Ipmi Error Codes

Page 103

Appendix A: BIOS POST Error Codes

Appendix A

BIOS Error Beep Codes

During the POST (Power-On Self-Test) routines, which are performed at each system boot, errors may occur.

Non-fatal errors are those which, in most cases, allow the system to continue to boot. The error messages normally appear on the screen.

Fatal errors will not allow the system to continue with bootup procedure. If a fatal error occurs, you should consult with your system manufacturer for possible repairs.

These fatal errors are usually communicated through a series of audible beeps. The numbers on the fatal error list correspond to the number of beeps for the corresponding error.

A-1 BIOS Error Beep Codes

BIOS Error Beep Codes

Beep Code/LED

1 beep

5 short beeps + 1 long beep

5 beeps

Error Message

Refresh

Memory error

No Con-In or No Con- Out devices

Description

Ready to boot

No memory detected in the system

Con-In: USB or PS/2 keyboard, PCI or Serial Console Redirection, IPMI KVM or SOL

Con-Out: Video Controller, PCI or Serial Console Redirection, IPMI SOL

1 Continuous Beep

X9 IPMI Error Codes

System OH	System Overheat

A-1

Image 103

Contents X9DRG-HF X9DRG-HTF Page About This Motherboard Manual Organization PrefaceConventions Used in the Manual Europe Contacting SupermicroAsia-Pacific Table of Contents Vii Appendix a Bios Error Beep Codes Overview ChecklistMotherboard Image Motherboard Layout PCH X9DRG-HF/X9DRG-HTF Quick ReferenceX9DRG-HF/X9DRG-HTF Connectors X9DRG-HF/X9DRG-HTF Jumpers Description Default SettingConnectors Description Description State Status X9DRG-HF/X9DRG-HTF LED IndicatorsCPU Motherboard FeaturesSuper I/O Sata ConnectionsIpmi Serial COM PortFan Control DimensionsPCI-E X8 G3 System Block DiagramProcessor and Chipset Overview PC Health Monitoring Special FeaturesRecovery from AC Power Loss Environmental Temperature ControlSuper I/O Acpi FeaturesPower Supply Slow Blinking LED for Suspend-State IndicatorManagement Engine ME Advanced Power ManagementIntel Intelligent Power Node Manager NM Overview of the Nuvoton WPCM450 ControllerWPCM450R DDR2 Memory Interface Other Features Supported by the Wpcm BMC ControllerWPCM450R PCI System Interface Page Standardized Warning Statements Battery HandlingPage 製品の廃棄 Product DisposalPage Installing the LGA2011 Processor Processor and Heatsink InstallationSocket Socket Keys CPU Keys Lever Lock Gently close the load plateScrew#1 Screw#2 Motherboard Installing a Passive CPU HeatsinkMounting Holes Removing the Heatsink Installing & Removing DIMMs Installing and Removing the Memory ModulesRemoving Memory Modules Processor and Memory Module Population Processors and their Corresponding Memory ModulesPopulating Udimm ECC/Non-ECC Memory Modules Intel E5-2600 Series Processor Udimm Memory Support Populating Lrdimm ECC Memory Modules Tools Needed Motherboard InstallationLocation of Mounting Holes Installing the Motherboard Back Panel Connectors and I/O Ports Control Panel Connectors and I/O PortsBack Panel I/O Port Locations and Definitions Video Connection Universal Serial Bus USBLAN Ports Pin Definition Ethernet PortsUID LED LE4 Unit Identifier SwitchFront Control Panel JF1 Header PinsFront Control Panel Pin Definitions Power LEDNMI Button NIC1/NIC2 LED Indicators HDD LED/UID SwitchOverheat OH/Fan Fail/PWR Fail/UID Power Fail LEDPower Button Reset ButtonPower Connectors Connecting CablesChassis Intrusion Fan HeadersOverheat LED/Fan Fail TPM Header/PortSGPIO1/2/-S Headers Power SMB I2C ConnectorsGlan Enable/Disable Jumper SettingsExplanation of Jumpers Cmos Clear Watch Dog Enable/DisableBMC Enable VGA EnableManufacture Mode Select Management Engine ME RecoveryGlan LEDs Onboard LED IndicatorsIpmi Dedicated LAN LEDs BMC Heartbeat LED Onboard Power LEDRear UID LED Serial ATA Ports Serial ATA ConnectionsBefore Power On Troubleshooting ProceduresNo Power Losing the System’s Setup Configuration System Boot FailureNo Video When the System Becomes Unstable Memory ErrorsSystem becomes unstable before or during OS installation Technical Support Procedures Battery Removal Battery Removal and InstallationProper Battery Disposal Battery Installation Frequently Asked Questions Returning Merchandise for Service Introduction Starting Bios Setup UtilityHow To Change the Configuration Data Main SetupStarting the Setup Utility Memory Information Total Memory System Date/System TimeSupermicro X9DRG-HF Version Build DateBoot Features Advanced Setup ConfigurationsCPU Configuration Power ConfigurationSocket 1 CPU Information/Socket 2 CPU Information Rtid Record Types IDs CPU Speed64-bit Clock Spread SpectrumActive Processor Cores MLC Streamer Prefetcher Available when supported by the CPUMLC Spatial Prefetch Available when supported by the CPU DCU Streamer Prefetcher Available when supported by the CPUTurbo Mode Available when Power Technology is set to Custom  CPU Power Management ConfigurationPower Technology Eist Available when Power Technology is set to CustomEnergy/Performance Bias Factory Long Duration Power LimitLong Duration Power Limit Recommended Short Duration PowerIntegrated IO Configuration Chipset Configuration North BridgeQPI Configuration Current Memory Speed Current Memory ModeMemory Mode Dram Rapl ModeDemand Scrub Channel InterleavingRank Interleaving Patrol ScrubSATA Configuration South Bridge ConfigurationAggressive Link Power Management Sata ModeIDE Mode Ahci ModePCIe/PCI/PnP Configuration SCU Storage Control Unit ConfigurationLoad Onboard LAN1 Option ROM/Load Onboard LAN2 Option ROM Maximum Read RequestAspm Support Onboard LAN Option ROM SelectSerial Port 1 Configuration Super IO ConfigurationSOL Configuration Serial Port Console Redirection Console Redirection SettingsStop Bits Recorder ModeResolution Legacy OS Redirection ResolutionOut-of-Band Management Port ACPI SettingsData Bits, Parity, Stop Bits TPM Enable Status ME Subsystem Intel TXT LT-SX ConfigurationWake on LAN NIC ConfigurationISCSI Initiator Name Link SpeedEnabling/Disabling Options Smbios Event Log Change Smbios Event Log SettingsEvent Logs Erasing Settings Erase Event Log Runtime Error Logging SupportMemory Correctable Error Threshold PCI Error Logging SupportSystem Event Log IpmiBMC Network Configuration Gateway IP Address BootSubnet Mask Station MAC AddressUser Password Delete Boot OptionDelete Boot Option Administrator PasswordSave Options Save Changes Save Changes and ResetSave & Exit Discard Changes and ExitBoot Override Restore Optimized DefaultsSave as User Defaults Restore User DefaultsBios Error Beep Codes Bios Error Beep CodesX9 Ipmi Error Codes X9DRG-HF/X9DRG-HTF Motherboard User’s Manual Driver/Tool Installation Display Screen Installing Software ProgramsConfiguring SuperDoctor SuperDoctor III Interface Display Screen-II Remote Control X9DRG-HF/X9DRG-HTF Motherboard User’s Manual