SUPER MICRO Computer X9DRG-HTF, X9DRG-HF user manual VGA Enable, BMC Enable

Page 57

Chapter 2: Installation

VGA Enable

Jumper JPG1 allows the user to enable the onboard VGA connector. The default setting is 1-2 to enable the connection. See the table on the right for jumper settings.

BMC Enable

Jumper JPB1 allows you to enable the embedded BMC (Baseboard Manage- ment) Controller to provide IPMI/KVM support on the motherboard. See the table on the right for jumper settings.

VGA Enable

Jumper Settings

Jumper Setting

 

Definition

1-2

 

Enabled (Default)

 

2-3

 

Disabled

 

 

 

 

BMC Enable

Jumper Settings

Jumper Setting Definition

Pins 1-2

BMC Enable

Pins 2-3

Normal (Default)

 

 

B

A

A. VGA Enabled

B. BMC Enabled

 

2-33

Page 56 Page 58
Image 57
Page 56 Page 58
Contents X9DRG-HF X9DRG-HTF Page About This Motherboard Manual Organization PrefaceConventions Used in the Manual Contacting Supermicro EuropeAsia-Pacific Table of Contents Vii Appendix a Bios Error Beep Codes Overview ChecklistMotherboard Image Motherboard Layout PCH X9DRG-HF/X9DRG-HTF Quick ReferenceX9DRG-HF/X9DRG-HTF Jumpers Description Default Setting X9DRG-HF/X9DRG-HTF ConnectorsConnectors Description Description State Status X9DRG-HF/X9DRG-HTF LED IndicatorsCPU Motherboard FeaturesIpmi Sata ConnectionsSerial COM Port Super I/OFan Control DimensionsPCI-E X8 G3 System Block DiagramProcessor and Chipset Overview Recovery from AC Power Loss Special FeaturesEnvironmental Temperature Control PC Health MonitoringPower Supply Acpi FeaturesSlow Blinking LED for Suspend-State Indicator Super I/OIntel Intelligent Power Node Manager NM Advanced Power ManagementOverview of the Nuvoton WPCM450 Controller Management Engine MEOther Features Supported by the Wpcm BMC Controller WPCM450R DDR2 Memory InterfaceWPCM450R PCI System Interface Page Standardized Warning Statements Battery HandlingPage 製品の廃棄 Product DisposalPage Installing the LGA2011 Processor Processor and Heatsink InstallationSocket Socket Keys CPU Keys Lever Lock Gently close the load plateInstalling a Passive CPU Heatsink Screw#1 Screw#2 MotherboardMounting Holes Removing the Heatsink Installing and Removing the Memory Modules Installing & Removing DIMMsRemoving Memory Modules Processor and Memory Module Population Processors and their Corresponding Memory ModulesPopulating Udimm ECC/Non-ECC Memory Modules Intel E5-2600 Series Processor Udimm Memory Support Populating Lrdimm ECC Memory Modules Motherboard Installation Tools NeededLocation of Mounting Holes Installing the Motherboard Control Panel Connectors and I/O Ports Back Panel Connectors and I/O PortsBack Panel I/O Port Locations and Definitions Video Connection Universal Serial Bus USBLAN Ports Pin Definition Ethernet PortsUID LED LE4 Unit Identifier SwitchFront Control Panel JF1 Header PinsPower LED Front Control Panel Pin DefinitionsNMI Button NIC1/NIC2 LED Indicators HDD LED/UID SwitchOverheat OH/Fan Fail/PWR Fail/UID Power Fail LEDPower Button Reset ButtonPower Connectors Connecting CablesChassis Intrusion Fan HeadersOverheat LED/Fan Fail TPM Header/Port SGPIO1/2/-S Headers Power SMB I2C ConnectorsJumper Settings Glan Enable/DisableExplanation of Jumpers Cmos Clear Watch Dog Enable/DisableBMC Enable VGA EnableManufacture Mode Select Management Engine ME RecoveryOnboard LED Indicators Glan LEDsIpmi Dedicated LAN LEDs BMC Heartbeat LED Onboard Power LEDRear UID LED Serial ATA Ports Serial ATA ConnectionsTroubleshooting Procedures Before Power OnNo Power System Boot Failure Losing the System’s Setup ConfigurationNo Video When the System Becomes Unstable Memory ErrorsSystem becomes unstable before or during OS installation Technical Support Procedures Battery Removal and Installation Battery RemovalProper Battery Disposal Battery Installation Frequently Asked Questions Returning Merchandise for Service Introduction Starting Bios Setup UtilityMain Setup How To Change the Configuration DataStarting the Setup Utility Supermicro X9DRG-HF Version System Date/System TimeBuild Date Memory Information Total MemoryBoot Features Advanced Setup ConfigurationsPower Configuration CPU ConfigurationSocket 1 CPU Information/Socket 2 CPU Information 64-bit CPU SpeedClock Spread Spectrum Rtid Record Types IDsMLC Spatial Prefetch Available when supported by the CPU MLC Streamer Prefetcher Available when supported by the CPUDCU Streamer Prefetcher Available when supported by the CPU Active Processor CoresPower Technology  CPU Power Management ConfigurationEist Available when Power Technology is set to Custom Turbo Mode Available when Power Technology is set to CustomLong Duration Power Limit Factory Long Duration Power LimitRecommended Short Duration Power Energy/Performance BiasIntegrated IO Configuration Chipset Configuration North BridgeQPI Configuration Memory Mode Current Memory ModeDram Rapl Mode Current Memory SpeedRank Interleaving Channel InterleavingPatrol Scrub Demand ScrubSATA Configuration South Bridge ConfigurationIDE Mode Sata ModeAhci Mode Aggressive Link Power ManagementPCIe/PCI/PnP Configuration SCU Storage Control Unit ConfigurationAspm Support Maximum Read RequestOnboard LAN Option ROM Select Load Onboard LAN1 Option ROM/Load Onboard LAN2 Option ROMSuper IO Configuration Serial Port 1 ConfigurationSOL Configuration Serial Port Console Redirection Console Redirection SettingsResolution Recorder ModeLegacy OS Redirection Resolution Stop BitsACPI Settings Out-of-Band Management PortData Bits, Parity, Stop Bits TPM Enable Status ME Subsystem Intel TXT LT-SX ConfigurationISCSI Initiator Name NIC ConfigurationLink Speed Wake on LANChange Smbios Event Log Settings Enabling/Disabling Options Smbios Event LogEvent Logs Memory Correctable Error Threshold Runtime Error Logging SupportPCI Error Logging Support Erasing Settings Erase Event LogSystem Event Log IpmiBMC Network Configuration Subnet Mask BootStation MAC Address Gateway IP AddressDelete Boot Option Delete Boot OptionAdministrator Password User PasswordSave & Exit Save Changes and ResetDiscard Changes and Exit Save Options Save ChangesSave as User Defaults Restore Optimized DefaultsRestore User Defaults Boot OverrideBios Error Beep Codes Bios Error Beep CodesX9 Ipmi Error Codes X9DRG-HF/X9DRG-HTF Motherboard User’s Manual Driver/Tool Installation Display Screen Installing Software ProgramsConfiguring SuperDoctor SuperDoctor III Interface Display Screen-II Remote Control X9DRG-HF/X9DRG-HTF Motherboard User’s Manual
Top Page Image Contents