SUPER MICRO Computer 1.2b user manual Hdd Led, NIC1/NIC2 LED Indicators

Page 46

X8DAH+/X8DAH+-F/X8DAH+(-F)-LR User's Manual

HDD LED

The HDD LED connection is located on pins 13 and 14 of JF1. Attach a cable here to indicate HDD activi- ties. See the table on the right for pin definitions.

HDD LED

Pin Definitions (JF1)

Pin# Definition

13+5V

14HD Active

NIC1/NIC2 LED Indicators

The NIC (Network Interface Control- ler) LED connection for GLAN port 1 is located on pins 11 and 12 of JF1, and the LED connection for GLAN Port 2 is on Pins 9 and 10. Attach the NIC LED cables to display network activity. Refer to the table on the right for pin definitions.

GLAN1/2 LED

Pin Definitions (JF1)

Pin# Definition

9/11

Vcc

10/12

Ground

 

 

A. HDD LED

B. NIC1 LED

C. NIC2 LED

 

20

19

 

 

Ground

NMI

 

 

 

 

 

X

X

 

 

Power LED

Vcc

 

 

A HDD LED

Vcc

 

 

 

 

 

B NIC1 LED

Vcc

 

 

C NIC2 LED

Vcc

 

X8DAH+ Rev. 2.01

OH/Fan Fail LED

Vcc

 

 

PWR Fail LED

Vcc

 

 

Ground

Reset

Reset Button

 

Ground

PWR

Power Button

 

 

 

2

1

 

 

2-22

 

 

Image 46
Contents X8DAH+ X8DAH+-F X8DAH+-LR X8DAH+-F-LR Page About this Manual About this Motherboard Manual OrganizationConventions Used in the Manual Europe Contacting SupermicroHeadquarters Asia-PacificTable of Contents Vii Bios IntroductionChecklist OverviewX8DAH+/X8DAH+-F/X8DAH+-F-LR Image Differences between X8DAH+/-F/-LR X8DAH+/X8DAH+-F/X8DAH+-F-LR LayoutYes Quick Reference VGA Enable Pins 1-2 Enabled X8DAH+-F/-LR only Compact Flash Enabled Closed EnabledSMB to PCI/PCI-E Slots Open/Open Disabled 1394-1/1394 Enable Pins 1-2 EnabledMemory Motherboard FeaturesChipset PC Health Monitoring Acpi FeaturesExpansion Slots Onboard I/OOther DimensionsCD/Diskette Utilities Introduction X8DAH+ System Diagram Block Diagram for the X8DAH+X8DAH+-F/-LR System Diagram Block Diagram for the X8DAH+-F/-LRChipset Overview Special Features PC Health MonitoringMain Switch Override Mechanism Acpi FeaturesSlow Blinking LED for Suspend-State Indicator System Resource AlertPower Supply Super I/OOverview of Winbond WPCM450 Controller For X8DAH+-F/-LR Only Page Installation Instructions Motherboard InstallationTools Needed Socket Clip Load Plate Processor and Heatsink InstallationInstalling an LGA 1366 Processor Plastic CapCPU Keys Load Plate Installing a CPU Heatsink Removing the Heatsink Dimm Installation Memory InstallationInstalling and Removing DIMMs Memory Support P1-DIMMs To Populate P1-DIMMs Branch P2-DIMMs To Populate P2-DIMMs BranchMemory Support for the Motherboard w/5500 CPUs Installed Memory Support for the Motherboard w/the 5600 CPUs Installed 35V DIMMs Possible System Memory Allocation & Availability TsegBack Panel Connectors/IO Ports Control Panel Connectors/IO PortsBack Panel Connectors Keyboard Purple Mouse Green ATX PS/2 Keyboard and PS/2 Mouse PortsPS/2 Keyboard/Mouse Pin Definitions COM VGA X8DAH+-F/-LR only Video Connector X8DAH+-F/-LRSerial Ports Serial Ports-COM1/COM2 Pin DefinitionsBack Panel USB USB 0/1, 2~5 Universal Serial Bus USBFront Panel USB Pin Definitions USB6/7, 8/9 LAN2 LAN1 Ipmi LAN X8DAH+-F/-LR only Ethernet PortsNC No Connection LAN Ports Pin DefinitionCD &10-pin Audio Headers Back Panel High Definition Audio HD AudioHD Audio See the graphics above for details CD1 Pin Audio Power Button JF1 Header PinsFront Control Panel Front Control Panel Pin Definitions Power LEDNMI Button NIC1/NIC2 LED Indicators HDD LEDOverheat OH/Fan Fail LED Power Fail LEDOH/Fan Fail & UID LEDs B. PWR Supply Fail Reset Button Pin Definitions JF1 Reset ButtonPower Button Power Button Pin Definitions JF1Required Connecting CablesPower Connectors Pin ATX PWR Reqd B/C.8-pin Processor PWR ReqdFan 1 B. Fan Fan HeadersChassis Intrusion Fan CPU1 Fan CPU2 Fan Chassis IntrusionInternal Speaker Power LED/SpeakerInternal Speaker Buzzer B. PWR LED/Speaker CNF1 1394a-1 Ieee 1394a ConnectionOverheat LED/Fan Fail JOH1 CNF2 1394a-2System Management Bus Power SMB I2C ConnectorSMB Header Pin Definitions Enabled Jumper SettingsGlan Enable/Disable Glan Port 1/2 EnableWatch Dog Jumper Settings JWD Watch Dog Enable/DisableClear Cmos Watch Dog Enable Cmos ClearCompact Flash Card Enable Jumper Settings Compact Flash EnableI2C for PCI/PCI-E slots Jumper Settings I2C Bus to PCI-Exp. SlotsVGA Enable VGA Enable X8DAH+-F/-LR Only1394a-1/1394a-2 Enable 1394a EnableGlan LEDs Onboard LED IndicatorsIpmi Dedicated LAN LEDs X8DAH+- F/-LR BMC Heartbeat LED X8DAH+-F Onboard Power LEDOnboard PWR LED B. BMC Heartbeat LED Floppy Connector Floppy Drive, Serial ATA and SAS ConnectionsIDE Connector BaleSata 0~5 Serial ATA PortsSerial ATA Pin Definitions Before Power On Troubleshooting ProceduresNo Power Memory Errors Losing the System’s Setup ConfigurationNo Video Technical Support Procedures Frequently Asked QuestionsReturning Merchandise for Service Starting Bios Setup Utility IntroductionHow To Change the Configuration Data Main SetupStarting the Setup Utility Processor System Time/System DateSuperMicro X8DAH System MemoryAdvanced Setup Configurations Boot FeaturePower Configuration Processor and Clock Options Active Processor Cores Intel AES-NI Available when supported by the OS and the CPUIntel Eist Technology CPU Bridge Configuration Advanced Chipset ControlQPI L0s and L1 Memory ModeQPI Frequency Memory FrequencyNorth Bridge Configuration South Bridge Configuration Configure SATA#1 as IDE/SATA ConfigurationSATA#1 Configuration SATA#2 ConfigurationPIO Mode Select Options Option Selected Max. Transfer Rate LBA/Large ModePIO Mode TypePCI/PnP Configuration Plug & Play OS PCI Latency TimerBoot Graphics Adapter Priority PCI IDE BusMasterSuper IO Device Configuration Remote Access ConfigurationHardware Health Monitor CPU 1 Temperature/CPU 2 Temperature/System Temperature CPU 1 Temperature/CPU 2 TemperatureFan Speed Control Modes Fan Speed ReadingsVoltage Readings ACPI Configuration Trusted Computing IPMI Configuration View BMC System Event LogSet LAN Configuration Event Log Configuration User Password Security SettingsSupervisor Password Change Supervisor PasswordPassword Check Available when a password is installed Boot ConfigurationBoot Device Priority Boot Sector Virus ProtectionCD/DVD Drives Hard Disk DrivesRemovable Drives USB DrivesExit Options Bios Error Beep Codes Bios Error Beep CodesBeep Code Error Message Description Page Appendix B Installing the Windows OS Installing the Windows OS to a RAID SystemInstalling the Windows OS to a Non-RAID System Installing Software Programs Driver/Tool Installation Display ScreenConfiguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control