SUPER MICRO Computer 1.2b user manual Compact Flash Enable, I2C Bus to PCI-Exp. Slots

Page 56

X8DAH+/X8DAH+-F/X8DAH+(-F)-LR User's Manual

I2C Bus to PCI-Exp. Slots

Jumpers JI2C1 and JI2C2 allow you to connect the System Management Bus (I2C) to PCI and PCI-Express slots. These two jumpers are to be set at the same time. The default setting is Open to disable the connections. See the table on the right for jumper settings.

I2C for PCI/PCI-E slots

Jumper Settings

Jumper Setting		Definition

Closed		Enabled

Open		Disabled (Default)

Compact Flash Enable

A Compact Flash Jumper is located at JPIDE1. To use a Compact Flash Card on this motherboard, you will need to close Pins 1~2 on this jumper to enable it. For the Compact Flash Card to work properly, please connect the Compact Flash Card power cable to JWF1 first. Refer to the board layout below for the location.

Compact Flash Card Enable

Jumper Settings

Jumper Definition

	Open	Disabled
	Closed	Enabled
	Closed	Enabled

		P2 DIMM3A	JPI2C1
FAN6	FAN5	P2 DIMM3B	PWR I2C
FAN6	FAN5	P2 DIMM3B	FAN7 CPU FAN1	JPW1	JPW2	JPW3

A. JI2C1

B. JI2C2

	KB/MS
COM1 (Bottom)	VGA (Top)
USB0/1	IPMI LAN	PHY
USB 2/3/4/5		Chip
USB 2/3/4/5		LAN2(Top)
(Bottom)		LAN2(Top)
LAN1
AUDIO
Header
	7.1HD AUDIO	CPU2 FAN
	CD1
Audio
CTRL

P2 DIMM3C

P2 DIMM2A

P2 DIMM2B

P2 DIMM2C

P2 DIMM1A

P2 DIMM1B

P2 DIMM1C

ALWAYS POPULATE DIMM1 FIRST

CPU2

Slot7 PCI-E 2.0 x8

Slot6 PCI-E 2.0 x16

CPU1

P1 DIMM1C

P1 DIMM1B

P1 DIMM1A

P1 DIMM2C

P1 DIMM2B

P1 DIMM2A

P1 DIMM3C

P1 DIMM3B

P1 DIMM3A

ALWAYS POPULATE DIMM1 FIRST

X8DAH+ Rev. 2.01

JD1

FAN2 JF1 FPCTL FAN1

SP1

C. Compact Flash En-

able

	Firmware	BA
	BMC	Slot5 PCI-E 2.0 x4 (in x8 Slot)
		JI2C2	JI2C1
	LAN		Slot4 PCI-E 2.0 x8 (in x16 Slot)
	CTRL
			Slot3 PCI-E 2.0 x8
	BMC
	CTRL		Slot2 PCI-E 2.0 x16
DP5	BMC Graphics
A	Memory		Slot1 PCI-E 2.0 x8
		1
			COM2
	JPG1	SMBUS1 JLPC80
	JPL1

DP4

				I-FAN2					FAN3
			Intel	I-FAN2
			IOH-36D					JBAT1
			IOH-36D
							BIOS
				Intel			JBT1	FLOPPY	IDE
				IOH-36D			JBT1	FLOPPY	IDE
							Intel
							ICH 10R
							(SouthBridge)	JIDE1	C
					JPI1		I-FAN1	JIDE1
				1394	JPI1		I-FAN1
S I/O	JPT1	J14	JP5	CTRL			I-SATA3 I-SATA1		FAN4
	JPT1	J14	J15 J139USB6/7	1394-1 1394-2			JUSB5		FAN4
			JP4				I-SATA5
JL1 JWD1			JUSB4 CNF1		CNF2	JP9 JUSB2	I-SATA4 I-SATA2 I-SATA0		JOH1

2-32

Image 56

Contents X8DAH+ X8DAH+-F X8DAH+-LR X8DAH+-F-LR Page About this Manual About this Motherboard Manual OrganizationConventions Used in the Manual Contacting Supermicro HeadquartersEurope Asia-PacificTable of Contents Vii Bios IntroductionChecklist OverviewX8DAH+/X8DAH+-F/X8DAH+-F-LR Image Yes X8DAH+/X8DAH+-F/X8DAH+-F-LR LayoutDifferences between X8DAH+/-F/-LR Quick Reference Compact Flash Enabled Closed Enabled SMB to PCI/PCI-E Slots Open/Open DisabledVGA Enable Pins 1-2 Enabled X8DAH+-F/-LR only 1394-1/1394 Enable Pins 1-2 EnabledChipset Motherboard FeaturesMemory Acpi Features Expansion SlotsPC Health Monitoring Onboard I/OCD/Diskette Utilities DimensionsOther Introduction X8DAH+ System Diagram Block Diagram for the X8DAH+X8DAH+-F/-LR System Diagram Block Diagram for the X8DAH+-F/-LRChipset Overview Special Features PC Health MonitoringAcpi Features Slow Blinking LED for Suspend-State IndicatorMain Switch Override Mechanism System Resource AlertPower Supply Super I/OOverview of Winbond WPCM450 Controller For X8DAH+-F/-LR Only Page Tools Needed Motherboard InstallationInstallation Instructions Processor and Heatsink Installation Installing an LGA 1366 ProcessorSocket Clip Load Plate Plastic CapCPU Keys Load Plate Installing a CPU Heatsink Removing the Heatsink Installing and Removing DIMMs Memory InstallationDimm Installation Memory Support P1-DIMMs To Populate P1-DIMMs Branch P2-DIMMs To Populate P2-DIMMs BranchMemory Support for the Motherboard w/5500 CPUs Installed Memory Support for the Motherboard w/the 5600 CPUs Installed 35V DIMMs Possible System Memory Allocation & Availability TsegBack Panel Connectors Control Panel Connectors/IO PortsBack Panel Connectors/IO Ports PS/2 Keyboard/Mouse Pin Definitions ATX PS/2 Keyboard and PS/2 Mouse PortsKeyboard Purple Mouse Green Video Connector X8DAH+-F/-LR Serial PortsCOM VGA X8DAH+-F/-LR only Serial Ports-COM1/COM2 Pin DefinitionsFront Panel USB Pin Definitions USB6/7, 8/9 Universal Serial Bus USBBack Panel USB USB 0/1, 2~5 Ethernet Ports NC No ConnectionLAN2 LAN1 Ipmi LAN X8DAH+-F/-LR only LAN Ports Pin DefinitionHD Audio See the graphics above for details CD1 Pin Audio Back Panel High Definition Audio HD AudioCD &10-pin Audio Headers Front Control Panel JF1 Header PinsPower Button NMI Button Power LEDFront Control Panel Pin Definitions NIC1/NIC2 LED Indicators HDD LEDOH/Fan Fail & UID LEDs B. PWR Supply Fail Power Fail LEDOverheat OH/Fan Fail LED Reset Button Power ButtonReset Button Pin Definitions JF1 Power Button Pin Definitions JF1Connecting Cables Power ConnectorsRequired Pin ATX PWR Reqd B/C.8-pin Processor PWR ReqdFan Headers Chassis IntrusionFan 1 B. Fan Fan CPU1 Fan CPU2 Fan Chassis IntrusionInternal Speaker Buzzer B. PWR LED/Speaker Power LED/SpeakerInternal Speaker Ieee 1394a Connection Overheat LED/Fan Fail JOH1CNF1 1394a-1 CNF2 1394a-2SMB Header Pin Definitions Power SMB I2C ConnectorSystem Management Bus Jumper Settings Glan Enable/DisableEnabled Glan Port 1/2 EnableWatch Dog Enable/Disable Clear Cmos Watch Dog EnableWatch Dog Jumper Settings JWD Cmos ClearCompact Flash Enable I2C for PCI/PCI-E slots Jumper SettingsCompact Flash Card Enable Jumper Settings I2C Bus to PCI-Exp. SlotsVGA Enable X8DAH+-F/-LR Only 1394a-1/1394a-2 EnableVGA Enable 1394a EnableIpmi Dedicated LAN LEDs X8DAH+- F/-LR Onboard LED IndicatorsGlan LEDs Onboard PWR LED B. BMC Heartbeat LED Onboard Power LEDBMC Heartbeat LED X8DAH+-F Floppy Connector Floppy Drive, Serial ATA and SAS ConnectionsIDE Connector BaleSerial ATA Pin Definitions Serial ATA PortsSata 0~5 No Power Troubleshooting ProceduresBefore Power On No Video Losing the System’s Setup ConfigurationMemory Errors Technical Support Procedures Frequently Asked QuestionsReturning Merchandise for Service Starting Bios Setup Utility IntroductionStarting the Setup Utility Main SetupHow To Change the Configuration Data System Time/System Date SuperMicro X8DAHProcessor System MemoryAdvanced Setup Configurations Boot FeaturePower Configuration Processor and Clock Options Intel Eist Technology Intel AES-NI Available when supported by the OS and the CPUActive Processor Cores CPU Bridge Configuration Advanced Chipset ControlMemory Mode QPI FrequencyQPI L0s and L1 Memory FrequencyNorth Bridge Configuration South Bridge Configuration IDE/SATA Configuration SATA#1 ConfigurationConfigure SATA#1 as SATA#2 ConfigurationLBA/Large Mode PIO ModePIO Mode Select Options Option Selected Max. Transfer Rate TypePCI/PnP Configuration PCI Latency Timer Boot Graphics Adapter PriorityPlug & Play OS PCI IDE BusMasterSuper IO Device Configuration Remote Access ConfigurationHardware Health Monitor CPU 1 Temperature/CPU 2 Temperature/System Temperature CPU 1 Temperature/CPU 2 TemperatureVoltage Readings Fan Speed ReadingsFan Speed Control Modes ACPI Configuration Trusted Computing IPMI Configuration View BMC System Event LogSet LAN Configuration Event Log Configuration Security Settings Supervisor PasswordUser Password Change Supervisor PasswordBoot Configuration Boot Device PriorityPassword Check Available when a password is installed Boot Sector Virus ProtectionHard Disk Drives Removable DrivesCD/DVD Drives USB DrivesExit Options Beep Code Error Message Description Bios Error Beep CodesBios Error Beep Codes Page Appendix B Installing the Windows OS Installing the Windows OS to a RAID SystemInstalling the Windows OS to a Non-RAID System Installing Software Programs Driver/Tool Installation Display ScreenConfiguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control