SUPER MICRO Computer 6015W-NTR Connecting Cables, Connecting Data Cables, Connecting Power Cables

Page 37

Chapter 5: Advanced Serverboard Setup

5-3 Connecting Cables

Now that the processors are installed, the next step is to connect the cables to the serverboard. These include the data (ribbon) cables for the peripherals and control panel and the power cables.

Connecting Data Cables

The cables used to transfer data from the peripheral devices have been carefully routed in preconﬁ gured systems to prevent them from blocking the ﬂ ow of cooling air that moves through the system from front to back. If you need to disconnect any of these cables, you should take care to reroute them as they were originally after reconnecting them (make sure the red wires connect to the pin 1 locations). If you are conﬁ guring the system, keep the airﬂ ow in mind when routing the cables.

The following data cables (with their serverboard connector locations noted) should be connected.

See the serverboard layout diagram in this chapter for connector locations.

•DVD-ROM Drive cable (IDE#1)

•Control Panel cable (JF1, see next page)

•SATA cables, 6015W-NTR/6015W-NT only (I-SATA0 ~ I-SATA3)

•SGPIO cable, 6015W-NTR/6015W-NT only (T-SGPIO1 to SATA backplane)

Connecting Power Cables

The X7DWU has a 20-pin primary power supply connector designated "JPW1" for connection to the ATX power supply. Connect the appropriate connector from the power supply to JPW1 to supply power to the serverboard. See the Connector Deﬁ nitions section in this chapter for power connector pin deﬁ nitions.

In addition, your power supply must be connected to the 4-pin Auxiliary ATX Power connection at JPW2 and the 8-pin Processor Power connector at JPW3.

Connecting the Control Panel

JF1 contains header pins for various front control panel connectors. See Figure 5-1 for the pin locations of the various front control panel buttons and LED indica- tors. Please note that even and odd numbered pins are on opposite sides of each header.

5-5

Image 37

Contents Super Manual Revision 1.0a Release Date April 23 About This Manual PrefaceManual Organization System Safety Preface Table of Contents System Interface Bios Overview Chapter IntroductionServerboard Features Server Chassis Features Backplane Front Control PanelCooling System CPU1 CPU2 Headquarters Contacting SupermicroEurope Asia-PaciﬁcPreparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Ambient Operating TemperatureInstalling the Inner Rails Installing the System into a RackIdentifying the Sections of the Rack Rails Installing the Rack Rails Installing the Outer RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackAccessing the Inside of the System Checking the Serverboard SetupChecking the Components Checking the Drives Checking the Drive Bay SetupChecking the Airﬂow Providing PowerChapter System Interface ResetControl Panel Buttons Control Panel LEDs PowerUniversal Information LED NIC2 Sata Drive Carrier LEDs Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsPrecautions Chapter Advanced Serverboard SetupHandling the Serverboard UnpackingInstalling the Processor Processor and Heatsink InstallationPage Removing the Heatsink Installing the HeatsinkConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control PanelI/O Ports Front Control Panel Header Pins JF1Installing DIMMs Installing MemoryMemory Support Installing Dimm into Slot Adding PCI Cards PCI Card InstallationPCI Expansion Slots PCI Slot/Card ConﬁgurationsSuper X7DWU Layout Serverboard DetailsX7DWU Quick Reference Jumper Description Default SettingConnector Deﬁnitions Universal Information LED HDD LEDReset Button Power Fail LEDPower Button Universal Serial Bus USB0/1Serial Ports Universal Serial Bus HeadersFan Headers ATX PS/2 Keyboard and PS/2 Mouse Ports Power LED/SpeakerOverheat LED Wake-On-LANLAN1/2 Ethernet Ports Wake-On-RingExplanation of Jumpers Jumper SettingsPower Force On VGA Enable/DisableLAN Enable/Disable Cmos ClearI2C Enable/Disable Watch Dog Enable/DisableMemory Voltage Select LAN1/LAN2 LEDs Onboard IndicatorsFloppy, IDE and Sata Drive Connections Floppy ConnectorSata Ports IDE ConnectorDriver Installation Display Screen Installing DriversStatic-Sensitive Devices Chapter Advanced Chassis SetupChassis Front and Rear Views Control PanelSystem Fan Failure System FansReplacing System Fans Removing the Front Bezel Drive Bay Installation/RemovalRemoving the Front Bezel Accessing the Drive BaysMounting a Sata Drive in a Drive Carrier Sata Drive InstallationRemoving a Sata Drive from the Server Installing/Removing a Sata DriveRemoving/Installing a Drive DVD-ROM and Floppy Drive InstallationRemoving the Chassis Cover Replacing the Power Supply Power Supply6015W-UR/6015W-NTR 6015W-U/6015W-NT Removing/Replacing the Power Supply Page Introduction ChapterMain Bios Setup Running SetupDefault settings are in bold text unless otherwise noted Press the Delete key to enter SetupBios Date Main Bios Setup Menu Main Setup FeaturesSystem Time System DateType IDE Channel 0 Master/Slave and Secondary IDE Master/ SlaveCHS Format Transfer Mode LBA Mode ControlUltra DMA Mode LBA FormatSerial ATA Sata RAID Enable Native Mode OperationICH RAID Code Base Available when Sata RAID is Enabled Sata Ahci Available when Sata RAID is DisabledBoot Features Advanced SetupQuickBoot Mode QuietBoot ModePower Button Behavior Acpi ModeEFI OS Boot Set Power On PasswordMemory Cache PCI Conﬁguration Advanced Chipset Control Intel VT for Directed I/O Memory Branch ModeMemory Voltage 4GB PCI Hole GranularityEnhanced x8 Detection High Temperature Dram OperationDemand Scrubbing AMB Thermal SensorAdvanced Processor Options Execute Disable Bit Available when supported by the CPU C1/C2 Enhanced Mode Available when supported by the CPUHardware Prefetcher Available when supported by the CPU Direct Cache Access Available when supported by the CPUDevice Conﬁguration DMI Event Logging Hardware Monitor Logic Console RedirectionVoltage Monitoring Fan Speed Control ModesAbled Bios Post Watch Dog Abled Bios Post ErrorsOS Boot Watch Dog Timer for Loading OS MinutesRealtime Sensor Data System Event Log/System Event Log List ModeUser Password Is Supervisor Password IsSet Supervisor Password SecurityPassword on Boot Set User PasswordTPM Trusted Platform Modules Support Current TPM StateBoot Priority Order/Excluded from Boot Orders BootExit Page Appendix a Bios Post Messages System timer error System Cmos checksum bad Default conﬁguration usedReal time clock error Check date and time settingsFail-Safe Timer NMI Failed System cache error Cache disabledAllocation Error for device Entering SetupFixed Disk n PS/2 Mouse Boot Summary ScreenInvalid System Conﬁguration Data Device IRQ conﬂictPress F2 to enter Setup Press F1 to resume, F2 to Setup, F3 for previousSystem Bios shadowed Video Bios shadowedPage Recoverable Post Errors Appendix B Bios Post CodesTerminal Post Errors RAM failure on data bits xxxx* of low byte of memory bus Post Code Description Inform RomPilot about the end of Post optional Following are for boot block in Flash ROM Page Processors Appendix C System SpeciﬁcationsExpansion Slots see -6 for details ChassisOperating Environment