SUPER MICRO Computer 6015W-NTR Adding PCI Cards, PCI Expansion Slots, PCI Card Installation

Page 41

Chapter 5: Advanced Serverboard Setup

5-6 Adding PCI Cards

PCI Expansion Slots

Two riser cards are used to support add-on cards to the system. The SC815TQ- R650U/SC815TQ-560U chassis can accommodate one standard size (full height full length) and one low proﬁ le PCI expansion card. When viewed from the chassis front, the standard size card installs to the left and the low-proﬁ le card installs to the right side.

PCI cards are installed into riser cards that have been pre-installed to the system. An additional two riser cards are included to support PCI-E add-on cards. See conﬁ guration list below.

PCI Card Installation

Before installing a PCI add-on card, make sure you install it into the correct riser card. Begin by releasing the locking tab that corresponds to the slot you wish to populate. Insert the expansion card into the correct riser card, pushing down with your thumbs evenly on both sides of the card.

PCI Slot/Card Conﬁgurations

6015W-UR/6015W-U

Left Side Riser Card

CSE-R1UU-UE8 (pre-installed)

Right Side Riser Card

RSC-R1UU-E8R (pre-installed)

6015W-NTR/6015W-NT

Left Side Riser Card

CSE-R1UU-2E8 (pre-installed)

Right Side Riser Card

RSC-R1UU-E8R (pre-installed)

Expansion card supported

1x UIO card and 1x PCI-E x8 card Expansion card supported

1x PCI-Express x8 card (maximum length of 5.5")

Expansion card supported 2x PCI-E x8 cards Expansion card supported 1x PCI-Express x8 card (maximum length of 5.5")

5-9

Image 41

Contents Super Manual Revision 1.0a Release Date April 23 Manual Organization PrefaceAbout This Manual System Safety Preface Table of Contents System Interface Bios Overview Chapter IntroductionServerboard Features Server Chassis Features Cooling System Front Control PanelBackplane CPU1 CPU2 Headquarters Contacting SupermicroEurope Asia-PaciﬁcUnpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Ambient Operating TemperatureIdentifying the Sections of the Rack Rails Installing the System into a RackInstalling the Inner Rails Installing the Rack Rails Installing the Outer RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Components Checking the Serverboard SetupAccessing the Inside of the System Checking the Drives Checking the Drive Bay SetupChecking the Airﬂow Providing PowerControl Panel Buttons ResetChapter System Interface Universal Information LED PowerControl Panel LEDs NIC2 Sata Drive Carrier LEDs Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsPrecautions Chapter Advanced Serverboard SetupHandling the Serverboard UnpackingInstalling the Processor Processor and Heatsink InstallationPage Removing the Heatsink Installing the HeatsinkConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control PanelI/O Ports Front Control Panel Header Pins JF1Memory Support Installing MemoryInstalling DIMMs Installing Dimm into Slot Adding PCI Cards PCI Card InstallationPCI Expansion Slots PCI Slot/Card ConﬁgurationsSuper X7DWU Layout Serverboard DetailsX7DWU Quick Reference Jumper Description Default SettingConnector Deﬁnitions Universal Information LED HDD LEDReset Button Power Fail LEDPower Button Universal Serial Bus USB0/1Fan Headers Universal Serial Bus HeadersSerial Ports ATX PS/2 Keyboard and PS/2 Mouse Ports Power LED/SpeakerOverheat LED Wake-On-LANLAN1/2 Ethernet Ports Wake-On-RingExplanation of Jumpers Jumper SettingsPower Force On VGA Enable/DisableLAN Enable/Disable Cmos ClearMemory Voltage Select Watch Dog Enable/DisableI2C Enable/Disable LAN1/LAN2 LEDs Onboard IndicatorsFloppy, IDE and Sata Drive Connections Floppy ConnectorSata Ports IDE ConnectorDriver Installation Display Screen Installing DriversStatic-Sensitive Devices Chapter Advanced Chassis SetupChassis Front and Rear Views Control PanelReplacing System Fans System FansSystem Fan Failure Removing the Front Bezel Drive Bay Installation/RemovalRemoving the Front Bezel Accessing the Drive BaysMounting a Sata Drive in a Drive Carrier Sata Drive InstallationRemoving a Sata Drive from the Server Installing/Removing a Sata DriveRemoving the Chassis Cover DVD-ROM and Floppy Drive InstallationRemoving/Installing a Drive 6015W-UR/6015W-NTR Power SupplyReplacing the Power Supply 6015W-U/6015W-NT Removing/Replacing the Power Supply Page Introduction ChapterMain Bios Setup Running SetupDefault settings are in bold text unless otherwise noted Press the Delete key to enter SetupBios Date Main Bios Setup Menu Main Setup FeaturesSystem Time System DateCHS Format IDE Channel 0 Master/Slave and Secondary IDE Master/ SlaveType Transfer Mode LBA Mode ControlUltra DMA Mode LBA FormatSerial ATA Sata RAID Enable Native Mode OperationICH RAID Code Base Available when Sata RAID is Enabled Sata Ahci Available when Sata RAID is DisabledBoot Features Advanced SetupQuickBoot Mode QuietBoot ModePower Button Behavior Acpi ModeEFI OS Boot Set Power On PasswordMemory Cache PCI Conﬁguration Advanced Chipset Control Intel VT for Directed I/O Memory Branch ModeMemory Voltage 4GB PCI Hole GranularityEnhanced x8 Detection High Temperature Dram OperationDemand Scrubbing AMB Thermal SensorAdvanced Processor Options Execute Disable Bit Available when supported by the CPU C1/C2 Enhanced Mode Available when supported by the CPUHardware Prefetcher Available when supported by the CPU Direct Cache Access Available when supported by the CPUDevice Conﬁguration DMI Event Logging Hardware Monitor Logic Console RedirectionVoltage Monitoring Fan Speed Control ModesAbled Bios Post Watch Dog Abled Bios Post ErrorsOS Boot Watch Dog Timer for Loading OS MinutesRealtime Sensor Data System Event Log/System Event Log List ModeUser Password Is Supervisor Password IsSet Supervisor Password SecurityPassword on Boot Set User PasswordTPM Trusted Platform Modules Support Current TPM StateBoot Priority Order/Excluded from Boot Orders BootExit Page Appendix a Bios Post Messages System timer error System Cmos checksum bad Default conﬁguration usedReal time clock error Check date and time settingsFail-Safe Timer NMI Failed System cache error Cache disabledAllocation Error for device Entering SetupFixed Disk n PS/2 Mouse Boot Summary ScreenInvalid System Conﬁguration Data Device IRQ conﬂictPress F2 to enter Setup Press F1 to resume, F2 to Setup, F3 for previousSystem Bios shadowed Video Bios shadowedPage Terminal Post Errors Appendix B Bios Post CodesRecoverable Post Errors RAM failure on data bits xxxx* of low byte of memory bus Post Code Description Inform RomPilot about the end of Post optional Following are for boot block in Flash ROM Page Processors Appendix C System SpeciﬁcationsExpansion Slots see -6 for details ChassisOperating Environment