SUPER MICRO Computer 6015W-UR, 6015W-NTR user manual Connector Deﬁnitions

Page 44

SUPERSERVER 6015W-UR/6015W-U/6015W-NTR/6015W-NT User's Manual

5-8 Connector Deﬁnitions

ATX Power Connector

The primary ATX power supply con- nector meets the SSI (Superset ATX) 20-pin speciﬁ cation. Make sure that the orientation of the connector is correct. See the table on the right for pin deﬁ nitions.

Auxiliary Power Connector

In addition to the Primary ATX power connector (above), the Auxiliary 4-pin connector at JPW2 must also be con- nected to your power supply. See the table on the right for pin deﬁ nitions.

Processor Power Connector

JPW3 must also be connected to the power supply to provide power for the processor(s). See the table on the right for pin deﬁ nitions.

NMI Button

The non-maskable interrupt button header is located on pins 19 and 20 of JF1. Refer to the table on the right for pin deﬁ nitions.

Power LED

The Power LED connection is located on pins 15 and 16 of JF1. Refer to the table on the right for pin deﬁ nitions.

ATX Power 20-pin Connector

Pin Deﬁnitions (JPW1)

	Pin#	Deﬁ nition	Pin #	Deﬁ nition
	11	+3.3V	1	+3.3V
	12	-12V		+3.3V
			2
	13	COM		COM
			3
	14	PS_ON		+5V
			4
	15	COM		COM
			5
	16	COM		+5V
			6
	17	COM		COM
			7
	18	Res (NC)		PWR_OK
			8
	19	+5V	9	5VSB

	20	+5V	10	+12V

Auxiliary Power

Pin Deﬁnitions (JPW2)

	Pins	Deﬁ nition
	1 & 2	Ground
	3 & 4	+12V
	3 & 4	+12V

Processor Power

Pin Deﬁnitions (JPW3)

	Pins	Deﬁ nition
	1 through 4	Ground
	5 through 8	+12V
	5 through 8	+12V

NMI Button

Pin Deﬁnitions (JF1)

Pin# Deﬁ nition

19Control

20Ground

Power LED

Pin Deﬁnitions (JF1)

Pin# Deﬁ nition

15Vcc

16Control

5-12

Image 44

Contents Super Manual Revision 1.0a Release Date April 23 Manual Organization PrefaceAbout This Manual System Safety Preface Table of Contents System Interface Bios Chapter Introduction OverviewServerboard Features Server Chassis Features Cooling System Front Control PanelBackplane CPU1 CPU2 Contacting Supermicro HeadquartersEurope Asia-PaciﬁcUnpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Ambient Operating Temperature Rack Mounting ConsiderationsIdentifying the Sections of the Rack Rails Installing the System into a RackInstalling the Inner Rails Installing the Outer Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Components Checking the Serverboard SetupAccessing the Inside of the System Checking the Drive Bay Setup Checking the DrivesProviding Power Checking the AirﬂowControl Panel Buttons ResetChapter System Interface Universal Information LED PowerControl Panel LEDs NIC2 Sata Drive Carrier LEDs Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Serverboard Setup PrecautionsHandling the Serverboard UnpackingProcessor and Heatsink Installation Installing the ProcessorPage Installing the Heatsink Removing the HeatsinkConnecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control PanelFront Control Panel Header Pins JF1 I/O PortsMemory Support Installing MemoryInstalling DIMMs Installing Dimm into Slot PCI Card Installation Adding PCI CardsPCI Expansion Slots PCI Slot/Card ConﬁgurationsServerboard Details Super X7DWU LayoutJumper Description Default Setting X7DWU Quick ReferenceConnector Deﬁnitions HDD LED Universal Information LEDPower Fail LED Reset ButtonPower Button Universal Serial Bus USB0/1Fan Headers Universal Serial Bus HeadersSerial Ports Power LED/Speaker ATX PS/2 Keyboard and PS/2 Mouse PortsOverheat LED Wake-On-LANWake-On-Ring LAN1/2 Ethernet PortsJumper Settings Explanation of JumpersVGA Enable/Disable Power Force OnLAN Enable/Disable Cmos ClearMemory Voltage Select Watch Dog Enable/DisableI2C Enable/Disable Onboard Indicators LAN1/LAN2 LEDsFloppy Connector Floppy, IDE and Sata Drive ConnectionsIDE Connector Sata PortsInstalling Drivers Driver Installation Display ScreenChapter Advanced Chassis Setup Static-Sensitive DevicesControl Panel Chassis Front and Rear ViewsReplacing System Fans System FansSystem Fan Failure Drive Bay Installation/Removal Removing the Front BezelAccessing the Drive Bays Removing the Front BezelSata Drive Installation Mounting a Sata Drive in a Drive CarrierInstalling/Removing a Sata Drive Removing a Sata Drive from the ServerRemoving the Chassis Cover DVD-ROM and Floppy Drive InstallationRemoving/Installing a Drive 6015W-UR/6015W-NTR Power SupplyReplacing the Power Supply 6015W-U/6015W-NT Removing/Replacing the Power Supply Page Chapter IntroductionRunning Setup Main Bios SetupDefault settings are in bold text unless otherwise noted Press the Delete key to enter SetupMain Bios Setup Menu Main Setup Features Bios DateSystem Time System DateCHS Format IDE Channel 0 Master/Slave and Secondary IDE Master/ SlaveType LBA Mode Control Transfer ModeUltra DMA Mode LBA FormatNative Mode Operation Serial ATA Sata RAID EnableICH RAID Code Base Available when Sata RAID is Enabled Sata Ahci Available when Sata RAID is DisabledAdvanced Setup Boot FeaturesQuickBoot Mode QuietBoot ModeAcpi Mode Power Button BehaviorEFI OS Boot Set Power On PasswordMemory Cache PCI Conﬁguration Advanced Chipset Control Memory Branch Mode Intel VT for Directed I/OMemory Voltage 4GB PCI Hole GranularityHigh Temperature Dram Operation Enhanced x8 DetectionDemand Scrubbing AMB Thermal SensorAdvanced Processor Options C1/C2 Enhanced Mode Available when supported by the CPU Execute Disable Bit Available when supported by the CPUHardware Prefetcher Available when supported by the CPU Direct Cache Access Available when supported by the CPUDevice Conﬁguration DMI Event Logging Console Redirection Hardware Monitor LogicFan Speed Control Modes Voltage MonitoringAbled Bios Post Errors Abled Bios Post Watch DogOS Boot Watch Dog Timer for Loading OS MinutesSystem Event Log/System Event Log List Mode Realtime Sensor DataSupervisor Password Is User Password IsSet Supervisor Password SecuritySet User Password Password on BootTPM Trusted Platform Modules Support Current TPM StateBoot Boot Priority Order/Excluded from Boot OrdersExit Page Appendix a Bios Post Messages System Cmos checksum bad Default conﬁguration used System timer errorReal time clock error Check date and time settingsSystem cache error Cache disabled Fail-Safe Timer NMI FailedAllocation Error for device Entering SetupPS/2 Mouse Boot Summary Screen Fixed Disk nInvalid System Conﬁguration Data Device IRQ conﬂictPress F1 to resume, F2 to Setup, F3 for previous Press F2 to enter SetupSystem Bios shadowed Video Bios shadowedPage Terminal Post Errors Appendix B Bios Post CodesRecoverable Post Errors RAM failure on data bits xxxx* of low byte of memory bus Post Code Description Inform RomPilot about the end of Post optional Following are for boot block in Flash ROM Page Appendix C System Speciﬁcations ProcessorsChassis Expansion Slots see -6 for detailsOperating Environment