SUPER MICRO Computer 6015W-UR, 6015W-NTR user manual Jumper Settings, Explanation of Jumpers

Page 50

SUPERSERVER 6015W-UR/6015W-U/6015W-NTR/6015W-NT User's Manual

SGPIO

The two headers labeled T-SGPIO1 and T-SGPIO2 are for SGPIO (Se- rial General Purpose Input/Output). SGPIO provides a bus between the SATA controller and the SATA drive backplane to provide SATA enclosure management functions. Connect the appropriate cables from the backplane to the SGPIO1 and SGPIO2 headers to utilize SATA management functions on your system.

SGPIO Header

Pin Definitions (T-SGPIO1, T-SGPIO2)

Pin#

Defi nition

Pin #

Defi nition

1

NC

2

NC

3

Ground

 

Data

4

5

Load

 

Ground

6

7

NC

 

NC

8

 

 

 

 

Note: NC indicates no connection.

5-9 Jumper Settings

Explanation of Jumpers

To modify the operation of the serverboard, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector. Pin 1 is identifi ed with a square solder pad on the printed cir- cuit board. See the diagram at right for an example of jumping pins 1 and 2. Refer to the serverboard layout page for jumper locations.

Note: On two-pin jumpers, "Closed" means the jumper is on and "Open" means the jumper is off the pins.

3 2 1

Connector

Pins

Jumper

3 2 1

Setting

5-18

Image 50
Contents Super Manual Revision 1.0a Release Date April 23 Manual Organization PrefaceAbout This Manual System Safety Preface Table of Contents System Interface Bios Chapter Introduction OverviewServerboard Features Server Chassis Features Cooling System Front Control PanelBackplane CPU1 CPU2 Europe Contacting SupermicroHeadquarters Asia-PacificUnpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Ambient Operating Temperature Rack Mounting ConsiderationsIdentifying the Sections of the Rack Rails Installing the System into a RackInstalling the Inner Rails Installing the Outer Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Components Checking the Serverboard SetupAccessing the Inside of the System Checking the Drive Bay Setup Checking the DrivesProviding Power Checking the AirflowControl Panel Buttons ResetChapter System Interface Universal Information LED PowerControl Panel LEDs NIC2 Sata Drive Carrier LEDs Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryHandling the Serverboard Chapter Advanced Serverboard SetupPrecautions UnpackingProcessor and Heatsink Installation Installing the ProcessorPage Installing the Heatsink Removing the HeatsinkConnecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control PanelFront Control Panel Header Pins JF1 I/O PortsMemory Support Installing MemoryInstalling DIMMs Installing Dimm into Slot PCI Expansion Slots PCI Card InstallationAdding PCI Cards PCI Slot/Card ConfigurationsServerboard Details Super X7DWU LayoutJumper Description Default Setting X7DWU Quick ReferenceConnector Definitions HDD LED Universal Information LEDPower Button Power Fail LEDReset Button Universal Serial Bus USB0/1Fan Headers Universal Serial Bus HeadersSerial Ports Overheat LED Power LED/SpeakerATX PS/2 Keyboard and PS/2 Mouse Ports Wake-On-LANWake-On-Ring LAN1/2 Ethernet PortsJumper Settings Explanation of JumpersLAN Enable/Disable VGA Enable/DisablePower Force On Cmos ClearMemory Voltage Select Watch Dog Enable/DisableI2C Enable/Disable Onboard Indicators LAN1/LAN2 LEDsFloppy Connector Floppy, IDE and Sata Drive ConnectionsIDE Connector Sata PortsInstalling Drivers Driver Installation Display ScreenChapter Advanced Chassis Setup Static-Sensitive DevicesControl Panel Chassis Front and Rear ViewsReplacing System Fans System FansSystem Fan Failure Drive Bay Installation/Removal Removing the Front BezelAccessing the Drive Bays Removing the Front BezelSata Drive Installation Mounting a Sata Drive in a Drive CarrierInstalling/Removing a Sata Drive Removing a Sata Drive from the ServerRemoving the Chassis Cover DVD-ROM and Floppy Drive InstallationRemoving/Installing a Drive 6015W-UR/6015W-NTR Power SupplyReplacing the Power Supply 6015W-U/6015W-NT Removing/Replacing the Power Supply Page Chapter IntroductionDefault settings are in bold text unless otherwise noted Running SetupMain Bios Setup Press the Delete key to enter SetupSystem Time Main Bios Setup Menu Main Setup FeaturesBios Date System DateCHS Format IDE Channel 0 Master/Slave and Secondary IDE Master/ SlaveType Ultra DMA Mode LBA Mode ControlTransfer Mode LBA FormatICH RAID Code Base Available when Sata RAID is Enabled Native Mode OperationSerial ATA Sata RAID Enable Sata Ahci Available when Sata RAID is DisabledQuickBoot Mode Advanced SetupBoot Features QuietBoot ModeEFI OS Boot Acpi ModePower Button Behavior Set Power On PasswordMemory Cache PCI Configuration Advanced Chipset Control Memory Voltage Memory Branch ModeIntel VT for Directed I/O 4GB PCI Hole GranularityDemand Scrubbing High Temperature Dram OperationEnhanced x8 Detection AMB Thermal SensorAdvanced Processor Options Hardware Prefetcher Available when supported by the CPU C1/C2 Enhanced Mode Available when supported by the CPUExecute Disable Bit Available when supported by the CPU Direct Cache Access Available when supported by the CPUDevice Configuration DMI Event Logging Console Redirection Hardware Monitor LogicFan Speed Control Modes Voltage MonitoringOS Boot Watch Dog Abled Bios Post ErrorsAbled Bios Post Watch Dog Timer for Loading OS MinutesSystem Event Log/System Event Log List Mode Realtime Sensor DataSet Supervisor Password Supervisor Password IsUser Password Is SecurityTPM Trusted Platform Modules Support Set User PasswordPassword on Boot Current TPM StateBoot Boot Priority Order/Excluded from Boot OrdersExit Page Appendix a Bios Post Messages Real time clock error System Cmos checksum bad Default configuration usedSystem timer error Check date and time settingsAllocation Error for device System cache error Cache disabledFail-Safe Timer NMI Failed Entering SetupInvalid System Configuration Data PS/2 Mouse Boot Summary ScreenFixed Disk n Device IRQ conflictSystem Bios shadowed Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup Video Bios shadowedPage Terminal Post Errors Appendix B Bios Post CodesRecoverable Post Errors RAM failure on data bits xxxx* of low byte of memory bus Post Code Description Inform RomPilot about the end of Post optional Following are for boot block in Flash ROM Page Appendix C System Specifications ProcessorsChassis Expansion Slots see -6 for detailsOperating Environment