SUPER MICRO Computer 6015W-NTR, 6015W-UR user manual Wake-On-Ring, LAN1/2 Ethernet Ports

Page 49

Chapter 5: Advanced Serverboard Setup

Wake-On-Ring

The Wake-On-Ring header is des- ignated JWOR. This function allows your computer to receive and "wake- up" by an incoming call to the modem when in suspend state. See the table on the right for pin deﬁ nitions. You must have a WOR card and cable to use this feature.

SMB

The System Management Bus header (for the PCI bus) is designated SMB. Connect the appropriate cable here to utilize SMB on your system. See the table on the right for pin deﬁ nitions.

SMBUS_PS

This header is for I2C, which may be used to monitor the status of the power supply. See the table on the right for pin deﬁ nitions.

LAN1/2 (Ethernet Ports)

Two Ethernet ports (designated LAN1 and LAN2) are located beside the VGA port on the I/O backplane. These ports accept RJ45 type cables.

Wake-On-Ring

Pin Deﬁnitions

(JWOR)

Pin# Deﬁ nition

1Ground (Black)

2Wake-up

SMB Header

Pin Deﬁnitions (SMB)

Pin# Deﬁ nition

1Data

2Ground

3Clock

4No Connection

SMBUS_PS (I2C)

Pin Deﬁnitions

Pin# Deﬁ nition

1Clock

2SMB Data

3N/A

4N/A

5N/A

5-17

Image 49

Contents Super Manual Revision 1.0a Release Date April 23 About This Manual PrefaceManual Organization System Safety Preface Table of Contents System Interface Bios Overview Chapter IntroductionServerboard Features Server Chassis Features Backplane Front Control PanelCooling System CPU1 CPU2 Headquarters Contacting SupermicroEurope Asia-PaciﬁcPreparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Ambient Operating TemperatureInstalling the Inner Rails Installing the System into a RackIdentifying the Sections of the Rack Rails Installing the Rack Rails Installing the Outer RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackAccessing the Inside of the System Checking the Serverboard SetupChecking the Components Checking the Drives Checking the Drive Bay SetupChecking the Airﬂow Providing PowerChapter System Interface ResetControl Panel Buttons Control Panel LEDs PowerUniversal Information LED NIC2 Sata Drive Carrier LEDs Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsPrecautions Chapter Advanced Serverboard SetupHandling the Serverboard UnpackingInstalling the Processor Processor and Heatsink InstallationPage Removing the Heatsink Installing the HeatsinkConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control PanelI/O Ports Front Control Panel Header Pins JF1Installing DIMMs Installing MemoryMemory Support Installing Dimm into Slot Adding PCI Cards PCI Card InstallationPCI Expansion Slots PCI Slot/Card ConﬁgurationsSuper X7DWU Layout Serverboard DetailsX7DWU Quick Reference Jumper Description Default SettingConnector Deﬁnitions Universal Information LED HDD LEDReset Button Power Fail LEDPower Button Universal Serial Bus USB0/1Serial Ports Universal Serial Bus HeadersFan Headers ATX PS/2 Keyboard and PS/2 Mouse Ports Power LED/SpeakerOverheat LED Wake-On-LANLAN1/2 Ethernet Ports Wake-On-RingExplanation of Jumpers Jumper SettingsPower Force On VGA Enable/DisableLAN Enable/Disable Cmos ClearI2C Enable/Disable Watch Dog Enable/DisableMemory Voltage Select LAN1/LAN2 LEDs Onboard IndicatorsFloppy, IDE and Sata Drive Connections Floppy ConnectorSata Ports IDE ConnectorDriver Installation Display Screen Installing DriversStatic-Sensitive Devices Chapter Advanced Chassis SetupChassis Front and Rear Views Control PanelSystem Fan Failure System FansReplacing System Fans Removing the Front Bezel Drive Bay Installation/RemovalRemoving the Front Bezel Accessing the Drive BaysMounting a Sata Drive in a Drive Carrier Sata Drive InstallationRemoving a Sata Drive from the Server Installing/Removing a Sata DriveRemoving/Installing a Drive DVD-ROM and Floppy Drive InstallationRemoving the Chassis Cover Replacing the Power Supply Power Supply6015W-UR/6015W-NTR 6015W-U/6015W-NT Removing/Replacing the Power Supply Page Introduction ChapterMain Bios Setup Running SetupDefault settings are in bold text unless otherwise noted Press the Delete key to enter SetupBios Date Main Bios Setup Menu Main Setup FeaturesSystem Time System DateType IDE Channel 0 Master/Slave and Secondary IDE Master/ SlaveCHS Format Transfer Mode LBA Mode ControlUltra DMA Mode LBA FormatSerial ATA Sata RAID Enable Native Mode OperationICH RAID Code Base Available when Sata RAID is Enabled Sata Ahci Available when Sata RAID is DisabledBoot Features Advanced SetupQuickBoot Mode QuietBoot ModePower Button Behavior Acpi ModeEFI OS Boot Set Power On PasswordMemory Cache PCI Conﬁguration Advanced Chipset Control Intel VT for Directed I/O Memory Branch ModeMemory Voltage 4GB PCI Hole GranularityEnhanced x8 Detection High Temperature Dram OperationDemand Scrubbing AMB Thermal SensorAdvanced Processor Options Execute Disable Bit Available when supported by the CPU C1/C2 Enhanced Mode Available when supported by the CPUHardware Prefetcher Available when supported by the CPU Direct Cache Access Available when supported by the CPUDevice Conﬁguration DMI Event Logging Hardware Monitor Logic Console RedirectionVoltage Monitoring Fan Speed Control ModesAbled Bios Post Watch Dog Abled Bios Post ErrorsOS Boot Watch Dog Timer for Loading OS MinutesRealtime Sensor Data System Event Log/System Event Log List ModeUser Password Is Supervisor Password IsSet Supervisor Password SecurityPassword on Boot Set User PasswordTPM Trusted Platform Modules Support Current TPM StateBoot Priority Order/Excluded from Boot Orders BootExit Page Appendix a Bios Post Messages System timer error System Cmos checksum bad Default conﬁguration usedReal time clock error Check date and time settingsFail-Safe Timer NMI Failed System cache error Cache disabledAllocation Error for device Entering SetupFixed Disk n PS/2 Mouse Boot Summary ScreenInvalid System Conﬁguration Data Device IRQ conﬂictPress F2 to enter Setup Press F1 to resume, F2 to Setup, F3 for previousSystem Bios shadowed Video Bios shadowedPage Recoverable Post Errors Appendix B Bios Post CodesTerminal Post Errors RAM failure on data bits xxxx* of low byte of memory bus Post Code Description Inform RomPilot about the end of Post optional Following are for boot block in Flash ROM Page Processors Appendix C System SpeciﬁcationsExpansion Slots see -6 for details ChassisOperating Environment