SUPER MICRO Computer C2SEA, C2SEE user manual Front Control Panel, JF1 Header Pins

Page 29

Chapter 2: Installation

2. Front Control Panel

JF1 contains header pins for various buttons and indicators that are normally located on a control panel at the front of the chassis. These connectors are designed speciﬁ- cally for use with Supermicro server chassis. See Figure 2-4 for the descriptions of the various control panel buttons and LED indicators. Refer to the following section for descriptions and pin deﬁnitions.

JF1 Header Pins

Power LED

HDD LED

NIC1 LED

LED_Anode+

C2SEA/C2SEE

OH/Fan Fail LED

Ground

2 1

LED_Anode+

Reset Button

Power Button

2-9

Image 29

Contents C2SEA C2SEE Page Conventions Used in the Manual About this Motherboard Manual OrganizationAsia-Paciﬁc Contacting Supermicro HeadquartersEurope Preface Table of Contents Vii Appendices TroubleshootingBios Overview Chapter IntroductionC2SEA Motherboard Image Introduction Differences between the C2SEA and C2SEE Models Motherboard LayoutConnectors Description Jumpers Description Default SettingLED Indicator Description C2SEA/C2SEE Quick ReferenceMemory Motherboard FeaturesDimensions System Block Diagram Block DiagramChipset Overview Intel ICH10 System FeaturesGraphics and Memory Controller Hub Gmch Direct Media Interface DMIAcpi Features Recovery from AC Power LossEnhanced Power Management PC Health MonitoringSlow Blinking LED for Suspend-State Indicator Power SupplyBios Support for USB Keyboard Wake-On-LAN WOLSuper I/O Versatile Media CapabilitiesHigh-Deﬁnition Audio and Hdmi Connections Virtualization Technology VT-dStatic-Sensitive Devices Motherboard InstallationInstalling an LGA 775 Processor Processor and Heatsink InstallationPage CPU Installing the HeatsinkRemoving the Heatsink Memory Support Installing DIMMsPossible System Memory Allocation & Availability Installing and Removing DIMMsBack Panel I/O Port Locations and Deﬁnitions Control Panel Connectors/IO PortsFront Control Panel JF1 Header PinsPWR LED connector Power LEDPin# Deﬁnition LEDAnode+ PWR LED Signal Front Control Panel Pin DeﬁnitionsOH/Fan Fail LED NIC1 LED IndicatorsOverheat/Fan Fail LED OH Power Button Reset ButtonReset PWR Button Pin# Deﬁnition Reset GroundATX/Auxiliary Power Connectors Connecting CablesPin ATX PWR Pin PWR +5VGlan 1 Giga-bit Ethernet Port Universal Serial Bus USBPin# Deﬁnitions +5V PO+ Ground USB 8/10 USB 6/9/11 Pin # Deﬁnition +5VOverheat LED B. Chassis Intrusion Overheat LED/Fan Fail JOH1Chassis Intrusion Fan Headers VGA ConnectorFan 1 CPU Fan Pin# Deﬁnition Ground +12V Tachometer PWR ModulationKeyboard/Mouse ATX PS/2 Keyboard and PS/2 Mouse PortsSerial Ports Wake-On-LAN Wake-On-RingPin# Deﬁnition Ground Wake-up Pin# Deﬁnition +5V Standby Ground Wake-upSMBPS1 Connector SMBPS1 ConnectorHigh-Deﬁnition Audio HDA High-Deﬁnition AudioCD Header Pin# Deﬁnition Left Stereo Signal Ground Right StereoFront Panel Audio Control Hdmi Connector C2SEA only PDIFOut ConnectorPin Location Deﬁnition Outside Ground Inside Pdif Signal Pin# Deﬁnition Ground Vcc Pdif SignalPin# Deﬁnition +5V Key Ground 13941/13942 Connections C2SEA onlyGlan Enable/Disable Jumper SettingsGlan Port 1 Enable Pin# Deﬁnition Enabled default DisabledIeee 1394a Enable Watch Dog Enable/DisableWatch Dog Enable 13941/13942 Enable Jumper Setting Deﬁnition Pins Reset DefaultJI2C1 JI2C2 PCI/PCI-E Slots to SMB SpeedsClear Cmos IDE Enable B. Audio Enable IDE Enable/Disable C2SEA OnlyAudio Enable USB Wake-Up Pin# Deﬁnition Enabled Disabled defaultOnboard Speaker En- able Onboard Speaker EnableGlan LED Indicators Onboard IndicatorsWhen viewing from the rear side of the chassis Activity LinkOnboard PWR LED Indicator LE1 Onboard Power LED LE1Printer Parallel Port Connector and IDE Hard Drive ConnectionsParallel Port Connector Iochrdy IDE Connector C2SEAOnlyNo Power Troubleshooting ProceduresBefore Power On No Video Memory ErrorsLosing the System’s Setup Conﬁguration Question What type of memory does my motherboard support? Technical Support ProceduresFrequently Asked Questions Question How do I utilize the onboard HD sound? Question How do I update my BIOS?Question Whats on the CD that came with my motherboard? Returning Merchandise for Service Page How To Change the Conﬁguration Data Starting Bios Setup UtilityStarting the Setup Utility IntroductionSystem Time/System Date Main SetupSystem Memory ProcessorXbios Features Advanced Setup ConﬁgurationsXacpi Conﬁguration Max Cpuid Value Limit Ratio Cmos SettingXProcessor & Clock Options Core-Multi-Processing Available when supported by the CPU XNorthBridge Conﬁguration XAdvanced Chipset SettingsXVideo Function Conﬁguration Active State Power Management Spread Spectrum ModeTV Standard HDA ControllerXide Conﬁguration Submenu Xusb ConﬁgurationPIO Mode LBA/Large ModeConﬁgure SATA#1 As Block Multi-Sector TransferA.R.T. For Hard disk drives DMA ModeBit Data Transfer Hard Disk Write ProtectXPCI/PnP Conﬁguration XSuper IO Conﬁguration Parallel Port ModeSerial Port1 Address Parallel Port I/O AddressXHardware Health Conﬁguration System Temperature CPU Temperature Fan Speed Control ModesFan1-Fan5 Speeds Voltage MonitoringSecurity Settings XRemovable Drives Boot ConﬁgurationXBoot Device Priority Exit Options Load Optimal DefaultsSave Changes and Exit Discard Changes and ExitLoad Fail-Safe Defaults Beep Code Error Message Description Appendix a Bios Error Beep CodesC2SEA/C2SEE User’s Manual D0h Uncompressed Initialization CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Driver/Tool Installation Display Screen Installing DriversConﬁguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control