SUPER MICRO Computer C2SEE, C2SEA user manual Troubleshooting, Bios, Appendices

Page 8

C2SEA/C2SEE User’s Manual

Chapter 3: Troubleshooting

3-1

Troubleshooting Procedures

3-1

 

Before Power On

3-1

 

No Power

3-1

 

No Video

3-2

 

Memory Errors

3-2

 

Losing the System’s Setup Configuration

3-2

3-2

Technical Support Procedures

3-3

3-3

Frequently Asked Questions

3-3

3-4

Returning Merchandise for Service

3-5

Chapter 4: BIOS

4-1 Introduction

4-1

4-2 Main BIOS Setup

4-2

4-3 Advanced Setup

4-4

4-4

Security Setup

4-17

4-5

Boot Settings

4-18

4-6

Exit

4-19

Appendices:

Appendix A: BIOS POST Error Codes

A-1

Appendix B: AMI BIOS POST Messages

B-1

Appendix C: Installing Software Programs and Drivers

C-1

viii

Image 8
Contents C2SEA C2SEE Page About this Motherboard Manual Organization Conventions Used in the ManualAsia-Pacific Contacting Supermicro HeadquartersEurope Preface Table of Contents Vii Appendices TroubleshootingBios Chapter Introduction OverviewC2SEA Motherboard Image Introduction Motherboard Layout Differences between the C2SEA and C2SEE ModelsJumpers Description Default Setting Connectors DescriptionLED Indicator Description C2SEA/C2SEE Quick ReferenceMotherboard Features MemoryDimensions Block Diagram System Block DiagramIntel ICH10 System Features Chipset OverviewGraphics and Memory Controller Hub Gmch Direct Media Interface DMIRecovery from AC Power Loss Acpi FeaturesEnhanced Power Management PC Health MonitoringPower Supply Slow Blinking LED for Suspend-State IndicatorBios Support for USB Keyboard Wake-On-LAN WOLVersatile Media Capabilities Super I/OHigh-Definition Audio and Hdmi Connections Virtualization Technology VT-dMotherboard Installation Static-Sensitive DevicesProcessor and Heatsink Installation Installing an LGA 775 ProcessorPage Installing the Heatsink CPURemoving the Heatsink Installing DIMMs Memory SupportInstalling and Removing DIMMs Possible System Memory Allocation & AvailabilityControl Panel Connectors/IO Ports Back Panel I/O Port Locations and DefinitionsJF1 Header Pins Front Control PanelPower LED PWR LED connectorPin# Definition LEDAnode+ PWR LED Signal Front Control Panel Pin DefinitionsOH/Fan Fail LED NIC1 LED IndicatorsOverheat/Fan Fail LED OH Reset Button Power ButtonReset PWR Button Pin# Definition Reset GroundConnecting Cables ATX/Auxiliary Power ConnectorsPin ATX PWR Pin PWR +5VUniversal Serial Bus USB Glan 1 Giga-bit Ethernet PortPin# Definitions +5V PO+ Ground USB 8/10 USB 6/9/11 Pin # Definition +5VOverheat LED B. Chassis Intrusion Overheat LED/Fan Fail JOH1Chassis Intrusion VGA Connector Fan HeadersFan 1 CPU Fan Pin# Definition Ground +12V Tachometer PWR ModulationKeyboard/Mouse ATX PS/2 Keyboard and PS/2 Mouse PortsSerial Ports Wake-On-Ring Wake-On-LANPin# Definition Ground Wake-up Pin# Definition +5V Standby Ground Wake-upSMBPS1 Connector SMBPS1 ConnectorHigh-Definition Audio HDA High-Definition AudioCD Header Pin# Definition Left Stereo Signal Ground Right StereoFront Panel Audio Control PDIFOut Connector Hdmi Connector C2SEA onlyPin Location Definition Outside Ground Inside Pdif Signal Pin# Definition Ground Vcc Pdif Signal13941/13942 Connections C2SEA only Pin# Definition +5V Key GroundJumper Settings Glan Enable/DisableGlan Port 1 Enable Pin# Definition Enabled default DisabledWatch Dog Enable/Disable Ieee 1394a EnableWatch Dog Enable 13941/13942 Enable Jumper Setting Definition Pins Reset DefaultJI2C1 JI2C2 PCI/PCI-E Slots to SMB SpeedsClear Cmos IDE Enable B. Audio Enable IDE Enable/Disable C2SEA OnlyAudio Enable Pin# Definition Enabled Disabled default USB Wake-UpOnboard Speaker Enable Onboard Speaker En- ableOnboard Indicators Glan LED IndicatorsWhen viewing from the rear side of the chassis Activity LinkOnboard Power LED LE1 Onboard PWR LED Indicator LE1Printer Parallel Port Connector and IDE Hard Drive ConnectionsParallel Port Connector IDE Connector C2SEAOnly IochrdyNo Power Troubleshooting ProceduresBefore Power On No Video Memory ErrorsLosing the System’s Setup Configuration Question What type of memory does my motherboard support? Technical Support ProceduresFrequently Asked Questions Question How do I utilize the onboard HD sound? Question How do I update my BIOS?Question Whats on the CD that came with my motherboard? Returning Merchandise for Service Page Starting Bios Setup Utility How To Change the Configuration DataStarting the Setup Utility IntroductionMain Setup System Time/System DateProcessor System MemoryAdvanced Setup Configurations Xbios FeaturesXacpi Configuration Max Cpuid Value Limit Ratio Cmos SettingXProcessor & Clock Options Core-Multi-Processing Available when supported by the CPU XAdvanced Chipset Settings XNorthBridge ConfigurationXVideo Function Configuration Spread Spectrum Mode Active State Power ManagementTV Standard HDA ControllerXusb Configuration Xide Configuration SubmenuLBA/Large Mode PIO ModeConfigure SATA#1 As Block Multi-Sector TransferDMA Mode A.R.T. For Hard disk drivesBit Data Transfer Hard Disk Write ProtectXPCI/PnP Configuration Parallel Port Mode XSuper IO ConfigurationSerial Port1 Address Parallel Port I/O AddressSystem Temperature CPU Temperature Fan Speed Control Modes XHardware Health ConfigurationFan1-Fan5 Speeds Voltage MonitoringSecurity Settings XRemovable Drives Boot ConfigurationXBoot Device Priority Load Optimal Defaults Exit OptionsSave Changes and Exit Discard Changes and ExitLoad Fail-Safe Defaults Appendix a Bios Error Beep Codes Beep Code Error Message DescriptionC2SEA/C2SEE User’s Manual Uncompressed Initialization Codes D0hBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Installing Drivers Driver/Tool Installation Display ScreenConfiguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control