SUPER MICRO Computer AS1020S-8 user manual Serverboard, Chassis, Weight, System Input Requirements

Page 100

AS1020S-8 User's Manual

Serverboard

Model: H8DSR-8 (Extended ATX form factor)

Dimensions: 12 x 13.05 in (305 x 332 mm)

Chassis

Model: SC813S+-500 Form Factor: 1U rackmount

Dimensions (both): (HxWxD) 1.7 x 17.2 x 27 in. (43 x 437 x 686 mm)

Weight

Gross (Bare Bone): 38 lbs (17.3 kg)

System Cooling (fan speed controlled by BIOS setting, Chp 7) Four (4) 4-cm counter-rotating fans

One (1) air shroud

System Input Requirements

AC Input Voltage: 100-240 VAC

Rated Input Current: 14A (115V) to 5A (230V)

Rated Input Frequency: 50-60 Hz

Power Supply

Rated Output Power: 500W (Model# SP502-1S, Part# PWS-0048)

Rated Output Voltages: +3.3V (21A), +5V (30A), +12VALL (39A), +5Vsb (2A)

BTU Rating

2750 BTUs/hr (for rated output power pof 500 W)

Operating Environment

Operating Temperature: 10º to 35º C (50º to 95º F)

Non-operating Temperature: -40º to 70º C (-40º to 158º F)

Operating Relative Humidity: 8% to 90% (non-condensing)

Non-operating Relative Humidity: 5 to 95% (non-condensing)

C-2

Image 100

Contents AS1020S-8 Manual Revision Release Date December 28 About This Manual PrefaceManual Organization System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosPreface Table of Contents Advanced Serverboard Setup HDD LED NIC1 LED NIC2 LEDAdvanced Chassis Setup JsledBios AppendicesPage Chapter Introduction OverviewServerboard Features Server Chassis Features Cooling System Serverworks HT-2000/1000 Chipset System Block Diagram Page Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Installing the Rack Rails Installing the System into a RackIdentifying the Sections of the Rails Installing the Chassis Rails Identifying the Sections of the RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Checking the Drive Bay Setup Accessing the drive baysCD-ROM and ﬂoppy disk drives Check the Scsi disk drivesSupplying power to the system Check the airﬂowChapter System Interface Control Panel ButtonsControl Panel LEDs Scsi Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Serverboard Setup PrecautionsHandling the Serverboard UnpackingInstalling the Processor install to the CPU#1 socket ﬁrst Processor and Heatsink InstallationMounting the Serverboard into a Chassis Page Installing the Heatsinks Installing HeatsinksConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel I/O PortsInstalling Memory SupportSide and Top Views of DDR Installation Optimizing memory performanceAdding PCI Cards PCI card installationPCI slots Serverboard Details H8DSR-8 Serverboard Layout Not drawn to scaleJumpers Description Default Setting Connectors DescriptionH8DSR-8 Quick Reference Onboard LEDs DescriptionConnector Deﬁnitions Primary ATX Power ConnectorProcessor Power Connector Secondary Power ConnectionPower LED Overheat/Fan Fail LEDPower Fail LED Reset ButtonPower Button USB0/1 Universal Serial Bus PortsUSB2/3 Headers Serial PortsFan Headers ATX PS/2 Keyboard and PS/2 Mouse PortsPower LED/Speaker SMB Power I2CJLAN1/2 Ethernet Ports Ipmb HeaderOverheat LED Wake-On-RingWake-On-LAN Chassis IntrusionExplanation Jumpers Jumper SettingsCmos Clear PCI-X Slot Frequency Select Onboard Speaker Enable/ DisableWatch Dog Scsi Controller Enable/ Disable Scsi Termination Enable/ DisableVGA Enable/Disable Power Force OnOnboard Indicators I2C to PCI Enable/Disable+3.3V Power LED JLAN1/JLAN2 LEDsScsi Activity LEDs Post Code LEDsFloppy Connector Floppy, IDE and Scsi Drive ConnectionsIDE Connector Scsi Connectors Diffsens TermpwrPage Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front and Rear ViewsInstalling a new fan System FansSystem Fan Failure Replacing System FansDrive Bay Installation/Removal Accessing the Drive BaysScsi Drive Installation Mounting a Scsi drive in a drive carrierInstalling/removing hot-swap Scsi drives CD-ROM and Floppy Drive Installation Power Supply Power Supply FailureRemoving/Replacing the Power Supply Removing the power supplyRemoving/Replacing the Power Supply Page Chapter Starting the Setup UtilityIntroduction Main Menu Advanced Settings MenuCPU Conﬁguration Sub-Menu IDE Conﬁguration DMA Mode A.R.TBit Data Transfer Hard Disk Write ProtectPCI/PnP Menu Floppy ConﬁgurationSuper IO Conﬁguration Chipset Menu North Bridge ConﬁgurationMCT Timing Mode User Conﬁguration ModeEnable Clock to All DIMMs ECC Conﬁguration Dram ECC EnablePower Down Control ECC Chip KillDram Scrub Redirect Dram BG ScrubAcpi Conﬁguration Advanced Acpi Conﬁguration ATA ConﬁgurationEvent Log Conﬁguration Hyper Transport Conﬁguration AMD PowerNow Conﬁguration Remote Access ConﬁgurationMPS Conﬁguration PCI Express ConﬁgurationCPU Overheat Temperature System Health MonitorSystem Fan Monitor Fan Speed Control ModesBoot Menu Boot Settings ConﬁgurationBoot Device Priority Hard Disk DrivesRemovable Drives CD/DVD DrivesSecurity Menu Exit MenuLoad Optimal Defaults Load Fail-Safe DefaultsPage Amibios Error Beep Codes Appendix a Bios Error Beep CodesBeep Code Error Message Description Page Appendix B Bios Post Checkpoint Codes Uncompressed Initialization CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Appendix C System Speciﬁcations Weight Power SupplyServerboard ChassisRegulatory Compliance