SUPER MICRO Computer AS1020S-8 user manual Control Panel, Chassis Front and Rear Views

Page 62

AS1020S-8 User's Manual

Figure 6-1. Chassis: Front and Rear Views

Slim CD-ROM Drive

Slim Floppy Drive

System LEDs

Control Panel

SCSI Drive Bays

System Reset

Main Power

Power Supply Module

USB Ports

PCI Expansion Slots (w/ riser cards)

Mouse/Keyboard

COM1 Port

Ethernet Ports

VGA Port

Ext. SCSI Port

6-2 Control Panel

The control panel (located on the front of the chassis) must be connected to the JF1 connector on the serverboard to provide you with system status indications. These wires have been bundled together as a ribbon cable to simplify the connec- tion. Connect the cable from JF1 on the serverboard to the appropriate header on the Control Panel PCB (printed circuit board). Make sure the red wire plugs into pin 1 on both connectors. Pull all excess cabling out of the airﬂ ow path.

The control panel LEDs inform you of system status. See "Chapter 3: System Interface" for details on the LEDs and the control panel buttons. Details on JF1 can be found in "Chapter 5: Advanced Serverboard Setup."

6-2

Image 62

Contents AS1020S-8 Manual Revision Release Date December 28 Manual Organization PrefaceAbout This Manual Advanced Chassis Setup System SafetyAdvanced Serverboard Setup BiosPreface Table of Contents Advanced Serverboard Setup HDD LED NIC1 LED NIC2 LEDAdvanced Chassis Setup JsledBios AppendicesPage Chapter Introduction OverviewServerboard Features Server Chassis Features Cooling System Serverworks HT-2000/1000 Chipset System Block Diagram Page Unpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Identifying the Sections of the Rails Installing the System into a RackInstalling the Rack Rails Installing the Chassis Rails Identifying the Sections of the RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup CD-ROM and ﬂoppy disk drives Checking the Drive Bay SetupAccessing the drive bays Check the Scsi disk drivesSupplying power to the system Check the airﬂowChapter System Interface Control Panel ButtonsControl Panel LEDs Scsi Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryHandling the Serverboard Chapter Advanced Serverboard SetupPrecautions UnpackingMounting the Serverboard into a Chassis Processor and Heatsink InstallationInstalling the Processor install to the CPU#1 socket ﬁrst Page Installing the Heatsinks Installing HeatsinksConnecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control Panel I/O PortsInstalling Memory SupportSide and Top Views of DDR Installation Optimizing memory performancePCI slots PCI card installationAdding PCI Cards Serverboard Details H8DSR-8 Serverboard Layout Not drawn to scaleH8DSR-8 Quick Reference Jumpers Description Default SettingConnectors Description Onboard LEDs DescriptionProcessor Power Connector Connector DeﬁnitionsPrimary ATX Power Connector Secondary Power ConnectionPower LED Overheat/Fan Fail LEDPower Button Power Fail LEDReset Button USB0/1 Universal Serial Bus PortsFan Headers USB2/3 HeadersSerial Ports ATX PS/2 Keyboard and PS/2 Mouse PortsJLAN1/2 Ethernet Ports Power LED/SpeakerSMB Power I2C Ipmb HeaderWake-On-LAN Overheat LEDWake-On-Ring Chassis IntrusionCmos Clear Jumper SettingsExplanation Jumpers Watch Dog Onboard Speaker Enable/ DisablePCI-X Slot Frequency Select VGA Enable/Disable Scsi Controller Enable/ DisableScsi Termination Enable/ Disable Power Force On+3.3V Power LED Onboard IndicatorsI2C to PCI Enable/Disable JLAN1/JLAN2 LEDsScsi Activity LEDs Post Code LEDsFloppy Connector Floppy, IDE and Scsi Drive ConnectionsIDE Connector Scsi Connectors Diffsens TermpwrPage Tools Required Chapter Advanced Chassis SetupStatic-Sensitive Devices Control Panel Chassis Front and Rear ViewsSystem Fan Failure Installing a new fanSystem Fans Replacing System FansDrive Bay Installation/Removal Accessing the Drive BaysScsi Drive Installation Mounting a Scsi drive in a drive carrierInstalling/removing hot-swap Scsi drives CD-ROM and Floppy Drive Installation Removing/Replacing the Power Supply Power SupplyPower Supply Failure Removing the power supplyRemoving/Replacing the Power Supply Page Introduction Starting the Setup UtilityChapter CPU Conﬁguration Sub-Menu Advanced Settings MenuMain Menu IDE Conﬁguration Bit Data Transfer DMA ModeA.R.T Hard Disk Write ProtectPCI/PnP Menu Floppy ConﬁgurationSuper IO Conﬁguration Chipset Menu North Bridge ConﬁgurationEnable Clock to All DIMMs MCT Timing ModeUser Conﬁguration Mode ECC Conﬁguration Dram ECC EnableDram Scrub Redirect Power Down ControlECC Chip Kill Dram BG ScrubEvent Log Conﬁguration ATA ConﬁgurationAcpi Conﬁguration Advanced Acpi Conﬁguration Hyper Transport Conﬁguration MPS Conﬁguration AMD PowerNow ConﬁgurationRemote Access Conﬁguration PCI Express ConﬁgurationSystem Fan Monitor CPU Overheat TemperatureSystem Health Monitor Fan Speed Control ModesBoot Menu Boot Settings ConﬁgurationRemovable Drives Boot Device PriorityHard Disk Drives CD/DVD DrivesSecurity Menu Exit MenuLoad Optimal Defaults Load Fail-Safe DefaultsPage Beep Code Error Message Description Appendix a Bios Error Beep CodesAmibios Error Beep Codes Page Appendix B Bios Post Checkpoint Codes Uncompressed Initialization CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Appendix C System Speciﬁcations Serverboard WeightPower Supply ChassisRegulatory Compliance