SUPER MICRO Computer AS1020S-8 user manual IDE Connector

Page 58

AS1020S-8 User's Manual

IDE Connector

IDE Drive Connector Pin Deﬁnitions (JIDE1)

There are no jumpers to con- ﬁgure the onboard IDE connec- tor. See the table on the right for pin deﬁ nitions.

Pin# Deﬁ nition

1Reset IDE

3 Host Data 7

5 Host Data 6

7 Host Data 5

9Host Data 4

11 Host Data 3

13Host Data 2

15Host Data 1

17Host Data 0

19Ground

21DRQ3

23 I/O Write

25I/O Read

27IOCHRDY

29DACK3

31 IRQ14

33 Addr1

35 Addr0

37Chip Select 0

39Activity

Pin # Deﬁ nition

2Ground

4Host Data 8

6 Host Data 9

8 Host Data 10

10Host Data 11

12Host Data 12

14Host Data 13

16Host Data 14

18Host Data 15

20Key

22Ground

24 Ground

26Ground

28BALE

30Ground

32 IOCS16

34 Ground

36 Addr2

38Chip Select 1

40Ground

5-24

Image 58

Contents AS1020S-8 Manual Revision Release Date December 28 About This Manual PrefaceManual Organization Advanced Chassis Setup System SafetyAdvanced Serverboard Setup BiosPreface Table of Contents Advanced Serverboard Setup HDD LED NIC1 LED NIC2 LEDAdvanced Chassis Setup JsledBios AppendicesPage Chapter Introduction OverviewServerboard Features Server Chassis Features Cooling System Serverworks HT-2000/1000 Chipset System Block Diagram Page Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Installing the Rack Rails Installing the System into a RackIdentifying the Sections of the Rails Installing the Chassis Rails Identifying the Sections of the RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup CD-ROM and ﬂoppy disk drives Checking the Drive Bay SetupAccessing the drive bays Check the Scsi disk drivesSupplying power to the system Check the airﬂowChapter System Interface Control Panel ButtonsControl Panel LEDs Scsi Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryHandling the Serverboard Chapter Advanced Serverboard SetupPrecautions UnpackingInstalling the Processor install to the CPU#1 socket ﬁrst Processor and Heatsink InstallationMounting the Serverboard into a Chassis Page Installing the Heatsinks Installing HeatsinksConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel I/O PortsInstalling Memory SupportSide and Top Views of DDR Installation Optimizing memory performanceAdding PCI Cards PCI card installationPCI slots Serverboard Details H8DSR-8 Serverboard Layout Not drawn to scaleH8DSR-8 Quick Reference Jumpers Description Default SettingConnectors Description Onboard LEDs DescriptionProcessor Power Connector Connector DeﬁnitionsPrimary ATX Power Connector Secondary Power ConnectionPower LED Overheat/Fan Fail LEDPower Button Power Fail LEDReset Button USB0/1 Universal Serial Bus PortsFan Headers USB2/3 HeadersSerial Ports ATX PS/2 Keyboard and PS/2 Mouse PortsJLAN1/2 Ethernet Ports Power LED/SpeakerSMB Power I2C Ipmb HeaderWake-On-LAN Overheat LEDWake-On-Ring Chassis IntrusionExplanation Jumpers Jumper SettingsCmos Clear PCI-X Slot Frequency Select Onboard Speaker Enable/ DisableWatch Dog VGA Enable/Disable Scsi Controller Enable/ DisableScsi Termination Enable/ Disable Power Force On+3.3V Power LED Onboard IndicatorsI2C to PCI Enable/Disable JLAN1/JLAN2 LEDsScsi Activity LEDs Post Code LEDsFloppy Connector Floppy, IDE and Scsi Drive ConnectionsIDE Connector Scsi Connectors Diffsens TermpwrPage Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front and Rear ViewsSystem Fan Failure Installing a new fanSystem Fans Replacing System FansDrive Bay Installation/Removal Accessing the Drive BaysScsi Drive Installation Mounting a Scsi drive in a drive carrierInstalling/removing hot-swap Scsi drives CD-ROM and Floppy Drive Installation Removing/Replacing the Power Supply Power SupplyPower Supply Failure Removing the power supplyRemoving/Replacing the Power Supply Page Chapter Starting the Setup UtilityIntroduction Main Menu Advanced Settings MenuCPU Conﬁguration Sub-Menu IDE Conﬁguration Bit Data Transfer DMA ModeA.R.T Hard Disk Write ProtectPCI/PnP Menu Floppy ConﬁgurationSuper IO Conﬁguration Chipset Menu North Bridge ConﬁgurationEnable Clock to All DIMMs MCT Timing ModeUser Conﬁguration Mode ECC Conﬁguration Dram ECC EnableDram Scrub Redirect Power Down ControlECC Chip Kill Dram BG ScrubAcpi Conﬁguration Advanced Acpi Conﬁguration ATA ConﬁgurationEvent Log Conﬁguration Hyper Transport Conﬁguration MPS Conﬁguration AMD PowerNow ConﬁgurationRemote Access Conﬁguration PCI Express ConﬁgurationSystem Fan Monitor CPU Overheat TemperatureSystem Health Monitor Fan Speed Control ModesBoot Menu Boot Settings ConﬁgurationRemovable Drives Boot Device PriorityHard Disk Drives CD/DVD DrivesSecurity Menu Exit MenuLoad Optimal Defaults Load Fail-Safe DefaultsPage Amibios Error Beep Codes Appendix a Bios Error Beep CodesBeep Code Error Message Description Page Appendix B Bios Post Checkpoint Codes Uncompressed Initialization CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Appendix C System Speciﬁcations Serverboard WeightPower Supply ChassisRegulatory Compliance