SMC Networks SMCWBR14-N2 manual Add/Edit Inbound Filter Rule, Action, Inbound Filter Rules List

Page 51

Add/Edit Inbound Filter Rule

Here you can add entries to the Inbound Filter Rules List below, or edit existing entries.

Name

Enter a name for the rule that is meaningful to you.

Action

The rule can either Allow or Deny messages.

Source IP Range

Define the ranges of Internet addresses this rule applies to. For a single IP address, enter the same address in both the Start and End boxes. Up to eight ranges can be entered. The Enable checkbox allows you to turn on or off specific entries in the list of ranges.

Save

Saves the new or edited Inbound Filter Rule in the following list. When finished updating the Inbound Filter Rules List, you must still click the Save Settings button at the top of the page to make the changes effective and permanent.

Inbound Filter Rules List

The section lists the current Inbound Filter Rules. An Inbound Filter Rule can be changed by clicking the Edit icon, or deleted by clicking the Delete icon. When you click the Edit icon, the item is highlighted, and the "Edit Inbound Filter Rule" section is activated for editing.

In addition to the filters listed here, two predefined filters are available wherever inbound filters can be applied:

Allow All

Permit any WAN user to access the related capability.

Deny All

Prevent all WAN users from accessing the related capability. (LAN users are not affected by Inbound Filter Rules.)

48

Image 51

Contents User Guide Limited Warranty Page Iii CE Mark Declaration of Conformance for EMI and Safety EECImportant Note FCC Radiation Exposure StatementTable of Contents SMCWBR14-N2 Package Contents AD-HOCIBSS Network Wireless LAN NetworkingChannel for each station Page Roaming in an ESS network diagram Introduction Hardware Overview Front Panel LED’s Getting Started ¾ Click Log Using the Configuration MenuBasicInternet BasicBasicWireless Wireless Channel Enable WirelessWireless Network Name Enable Auto Channel ScanWPA-Personal WEPExample WPA-Personal and WPA-EnterpriseAdvanced Optional Backup Radius Server BasicNetwork Settings IP Address Router SettingsEnable RIP RIP Operating modeDhcp Server Settings Act as default routerAllow RIP updates from WAN RIP PasswordComputer Name Dhcp Lease TimeAlways Broadcast Add/Edit Dhcp ReservationReserve Dhcp Reservations ListNumber of Dynamic Dhcp Clients RevokeAdvancedVirtual Server AdvancedPublic Port Virtual Server Parameters NameProtocol Private PortSave EnableSchedule Add/Edit Virtual ServerAdvancedSpecial Applications Parameters for an Application Rule ExampleApplication Input Protocol Trigger Port RangeTrigger Protocol Input Port RangeAdvancedGaming Edit/Add Game Rule Port Forwarding Fields NameTCP Ports To Open UDP Ports To OpenAdvancedStreamEngine StreamEngine Setup Enable StreamEngineMeasured Uplink Speed Automatic ClassificationDynamic Fragmentation Automatic Uplink SpeedSource Port Range Add/Edit StreamEngine Rule EnablePriority Source IP RangeAdd/Edit Route AdvancedRoutingRoutes List AdvancedAccess Control Policy WizardAdd Policy Policy Table AdvancedWEB Filter Web Filter Parameters Web SiteAdd/Edit Web Site Allowed Web Site List AdvancedMAC Address Filter Enable MAC Address FilterFilter Settings Mode Filter Wireless ClientsFilter Wired Clients Add/Edit MAC AddressMAC Address List AdvancedFirewall Address Restricted Firewall Settings Enable SPINAT Endpoint Filtering Endpoint IndependentEnable DMZ DMZ HostDMZ IP Address Rtsp PptpWake-On-LAN FTPNetmeeting SIPAdvancedInbound Filter Allow All Add/Edit Inbound Filter RuleAction Inbound Filter Rules ListAdvancedAdvanced Wireless WDS Enable 802.11d EnableWMM Enable Extra Wireless ProtectionUPnP Enable UPnPEnable WAN Ping Respond AdvancedNetworkMulticast Streams Enable Multicast StreamsAdvancedWISH WAN Port SpeedHttp WishHost 2 IP Range Save/UpdateHost 1 IP Range Host 1 Port RangePIN Settings AdvancedWi-Fi Protected SetupWi-Fi Protected Setup Enable Lock Wireless Security SettingsGenerate New PIN Reset PIN to DefaultAdd Wireless Device Wizard Current PINTools ToolsAdminRemote Admin Port Admin PasswordUser Password Enable Remote ManagementTime Zone Time Configuration Current Router TimeEnable Daylight Saving ToolsTimeNTP Server Used Automatic Time Configuration Enable NTP ServerDaylight Saving Offset DST Start and DST EndEnable Logging to Syslog Server ToolsSyslogSyslog Server IP Address ToolsEmail Settings Verify Password Email Log When Full or on Schedule On Log FullOn Schedule Reboot The Device Save Settings To Local Hard DriveLoad Settings From Local Hard Drive Restore To Factory Default SettingsCheck Online Firmware UpgradeToolsFirmware Firmware InformationUpload ToolsDynamic DNS Timeout ToolsSystem Check ToolsSchedules Schedule Rules List Statistics and Active Sessions StatusDevice infoLAN Computers Dhcp ConnectionPPPoE, PPTP, L2TP Connection BigPond ConnectionStatusWireless SignalRate StatusRouting View Levels Apply Log Settings NowStatusLogs What to ViewRefresh Email NowSave Log StatusStatistics NAT StatusActive SessionsInternal ExternalTime Out StatusWISH SessionsDir OutTarget OriginatorEstablished or closing TCP connections Ascii AdslBootp CAT DMZ DhcpDNS DSLEAP GUI Igmp HttpsIcmp IeeeISP IPXL2TP LANLED LPR/LPDMTU MdixMIB MppeOSI NICNTP OfdmPPP RadiusRIP Soho RSASmtp SnmpTftp SsidTCP TCP/IPVlan URLUSB UTPWPA WDSWisp Wlan802.11 Yagi antennaTechnical Support