SMC Networks SMCWBR14-N2 manual Ppp, Radius, Rip

Page 97

Port

A logical channel endpoint in a network. A computer might have only one physical channel (its Ethernet channel) but can have multiple ports (logical channels) each identified by a number.

PPP

Point-to-Point Protocol is used for two computers to communicate with each over a serial interface, like a phone line

PPPoE

Point-to-Point Protocol over Ethernet is used to connect multiple computers to a remote server over Ethernet

PPTP

Point-to-Point Tunneling Protocol is used for creating VPN tunnels over the Internet between two networks

Preamble

Used to synchronize communication timing between devices on a network

Q

QoS

Quality of Service

R

RADIUS

Remote Authentication Dial-In User Service allows for remote users to dial into a central server and be authenticated in order to access resources on a network

Reboot

To restart a computer and reload it's operating software or firmware from nonvolatile storage.

Rendezvous

Apple's version of UPnP, which allows for devices on a network to discover each other and be connected without the need to configure any settings

Repeater

Retransmits the signal of an Access Point in order to extend it's coverage

RIP

Routing Information Protocol is used to synchronize the routing table of all the routers on a network

RJ-11

The most commonly used connection method for telephones

94

Image 97

Contents User Guide Limited Warranty Page Important Note CE Mark Declaration of Conformance for EMI and Safety EECFCC Radiation Exposure Statement IiiTable of Contents SMCWBR14-N2 Package Contents AD-HOCIBSS Network Wireless LAN NetworkingChannel for each station Page Roaming in an ESS network diagram Introduction Hardware Overview Front Panel LED’s Getting Started ¾ Click Log Using the Configuration MenuBasicInternet BasicBasicWireless Wireless Network Name Enable WirelessEnable Auto Channel Scan Wireless ChannelExample WEPWPA-Personal and WPA-Enterprise WPA-PersonalAdvanced Optional Backup Radius Server BasicNetwork Settings Enable RIP Router SettingsRIP Operating mode IP AddressAllow RIP updates from WAN Act as default routerRIP Password Dhcp Server SettingsAlways Broadcast Dhcp Lease TimeAdd/Edit Dhcp Reservation Computer NameNumber of Dynamic Dhcp Clients Dhcp Reservations ListRevoke ReserveAdvancedVirtual Server AdvancedProtocol Virtual Server Parameters NamePrivate Port Public PortSchedule EnableAdd/Edit Virtual Server SaveParameters for an Application Rule Example AdvancedSpecial ApplicationsApplication Trigger Protocol Trigger Port RangeInput Port Range Input ProtocolAdvancedGaming TCP Ports To Open Port Forwarding Fields NameUDP Ports To Open Edit/Add Game RuleAdvancedStreamEngine StreamEngine Setup Enable StreamEngineDynamic Fragmentation Automatic ClassificationAutomatic Uplink Speed Measured Uplink SpeedPriority Add/Edit StreamEngine Rule EnableSource IP Range Source Port RangeAdd/Edit Route AdvancedRoutingRoutes List Policy Wizard AdvancedAccess ControlAdd Policy Policy Table Web Filter Parameters Web Site AdvancedWEB FilterAdd/Edit Web Site Allowed Web Site List Filter Settings Mode Enable MAC Address FilterFilter Wireless Clients AdvancedMAC Address FilterAdd/Edit MAC Address Filter Wired ClientsMAC Address List AdvancedFirewall NAT Endpoint Filtering Firewall Settings Enable SPIEndpoint Independent Address RestrictedDMZ Host Enable DMZDMZ IP Address Rtsp PptpNetmeeting FTPSIP Wake-On-LANAdvancedInbound Filter Action Add/Edit Inbound Filter RuleInbound Filter Rules List Allow AllAdvancedAdvanced Wireless WMM Enable 802.11d EnableExtra Wireless Protection WDS EnableEnable WAN Ping Respond Enable UPnPAdvancedNetwork UPnPAdvancedWISH Enable Multicast StreamsWAN Port Speed Multicast StreamsHttp WishHost 1 IP Range Save/UpdateHost 1 Port Range Host 2 IP RangeWi-Fi Protected Setup Enable AdvancedWi-Fi Protected SetupLock Wireless Security Settings PIN SettingsAdd Wireless Device Wizard Reset PIN to DefaultCurrent PIN Generate New PINTools ToolsAdminUser Password Admin PasswordEnable Remote Management Remote Admin PortEnable Daylight Saving Time Configuration Current Router TimeToolsTime Time ZoneDaylight Saving Offset Automatic Time Configuration Enable NTP ServerDST Start and DST End NTP Server UsedToolsSyslog Enable Logging to Syslog ServerSyslog Server IP Address ToolsEmail Settings Email Log When Full or on Schedule On Log Full Verify PasswordOn Schedule Load Settings From Local Hard Drive Save Settings To Local Hard DriveRestore To Factory Default Settings Reboot The DeviceToolsFirmware Firmware UpgradeFirmware Information Check OnlineUpload ToolsDynamic DNS Timeout ToolsSystem Check ToolsSchedules Schedule Rules List Statistics and Active Sessions StatusDevice infoPPPoE, PPTP, L2TP Connection Dhcp ConnectionBigPond Connection LAN ComputersSignal StatusWirelessRate StatusRouting StatusLogs Apply Log Settings NowWhat to View View LevelsEmail Now RefreshSave Log StatusStatistics Internal StatusActive SessionsExternal NATDir StatusWISH SessionsOut Time OutTarget OriginatorEstablished or closing TCP connections Ascii AdslBootp CAT DMZ DhcpDSL DNSEAP GUI Icmp HttpsIeee IgmpISP IPXLED LANLPR/LPD L2TPMIB MdixMppe MTUNTP NICOfdm OSIRadius PPPRIP Smtp RSASnmp SohoTCP SsidTCP/IP TftpUSB URLUTP VlanWisp WDSWlan WPA802.11 Yagi antennaTechnical Support