SMC Networks SMCWBR14-N2 manual StatusWireless, Rate, Signal

Page 77

Status_Wireless

The wireless section allows you to view the wireless clients that are connected to your wireless router.

MAC Address

The Ethernet ID (MAC address) of the wireless client.

IP Address

The LAN-side IP address of the client.

Mode

The transmission standard being used by the client. Values are 11a, 11b, or 11g for 802.11a, 802.11b, or 802.11g respectively.

Rate

The actual transmission rate of the client in megabits per second.

Signal

This is a relative measure of signal quality. The value is expressed as a percentage of theoretical best quality. Signal quality can be reduced by distance, by interference from other radio-frequency sources (such as cordless telephones or neighboring wireless networks), and by obstacles between the router and the wireless device.

Image 77

Contents User Guide Limited Warranty Page Important Note CE Mark Declaration of Conformance for EMI and Safety EECFCC Radiation Exposure Statement IiiTable of Contents SMCWBR14-N2 Package Contents AD-HOCIBSS Network Wireless LAN NetworkingChannel for each station Page Roaming in an ESS network diagram Introduction Hardware Overview Front Panel LED’s Getting Started ¾ Click Log Using the Configuration MenuBasicInternet BasicBasicWireless Wireless Network Name Enable WirelessEnable Auto Channel Scan Wireless ChannelExample WEPWPA-Personal and WPA-Enterprise WPA-PersonalAdvanced Optional Backup Radius Server BasicNetwork Settings Enable RIP Router SettingsRIP Operating mode IP AddressAllow RIP updates from WAN Act as default routerRIP Password Dhcp Server SettingsAlways Broadcast Dhcp Lease TimeAdd/Edit Dhcp Reservation Computer NameNumber of Dynamic Dhcp Clients Dhcp Reservations ListRevoke ReserveAdvancedVirtual Server AdvancedProtocol Virtual Server Parameters NamePrivate Port Public PortSchedule EnableAdd/Edit Virtual Server SaveApplication AdvancedSpecial ApplicationsParameters for an Application Rule Example Trigger Protocol Trigger Port RangeInput Port Range Input ProtocolAdvancedGaming TCP Ports To Open Port Forwarding Fields NameUDP Ports To Open Edit/Add Game RuleAdvancedStreamEngine StreamEngine Setup Enable StreamEngineDynamic Fragmentation Automatic ClassificationAutomatic Uplink Speed Measured Uplink SpeedPriority Add/Edit StreamEngine Rule EnableSource IP Range Source Port RangeAdd/Edit Route AdvancedRoutingRoutes List Add Policy AdvancedAccess ControlPolicy Wizard Policy Table Add/Edit Web Site AdvancedWEB FilterWeb Filter Parameters Web Site Allowed Web Site List Filter Settings Mode Enable MAC Address FilterFilter Wireless Clients AdvancedMAC Address FilterMAC Address List Filter Wired ClientsAdd/Edit MAC Address AdvancedFirewall NAT Endpoint Filtering Firewall Settings Enable SPIEndpoint Independent Address RestrictedDMZ IP Address Enable DMZDMZ Host Rtsp PptpNetmeeting FTPSIP Wake-On-LANAdvancedInbound Filter Action Add/Edit Inbound Filter RuleInbound Filter Rules List Allow AllAdvancedAdvanced Wireless WMM Enable 802.11d EnableExtra Wireless Protection WDS EnableEnable WAN Ping Respond Enable UPnPAdvancedNetwork UPnPAdvancedWISH Enable Multicast StreamsWAN Port Speed Multicast StreamsHttp WishHost 1 IP Range Save/UpdateHost 1 Port Range Host 2 IP RangeWi-Fi Protected Setup Enable AdvancedWi-Fi Protected SetupLock Wireless Security Settings PIN SettingsAdd Wireless Device Wizard Reset PIN to DefaultCurrent PIN Generate New PINTools ToolsAdminUser Password Admin PasswordEnable Remote Management Remote Admin PortEnable Daylight Saving Time Configuration Current Router TimeToolsTime Time ZoneDaylight Saving Offset Automatic Time Configuration Enable NTP ServerDST Start and DST End NTP Server UsedSyslog Server IP Address Enable Logging to Syslog ServerToolsSyslog ToolsEmail Settings On Schedule Verify PasswordEmail Log When Full or on Schedule On Log Full Load Settings From Local Hard Drive Save Settings To Local Hard DriveRestore To Factory Default Settings Reboot The DeviceToolsFirmware Firmware UpgradeFirmware Information Check OnlineUpload ToolsDynamic DNS Timeout ToolsSystem Check ToolsSchedules Schedule Rules List Statistics and Active Sessions StatusDevice infoPPPoE, PPTP, L2TP Connection Dhcp ConnectionBigPond Connection LAN ComputersRate StatusWirelessSignal StatusRouting StatusLogs Apply Log Settings NowWhat to View View LevelsSave Log RefreshEmail Now StatusStatistics Internal StatusActive SessionsExternal NATDir StatusWISH SessionsOut Time OutTarget OriginatorEstablished or closing TCP connections Ascii AdslBootp CAT DMZ DhcpEAP DNSDSL GUI Icmp HttpsIeee IgmpISP IPXLED LANLPR/LPD L2TPMIB MdixMppe MTUNTP NICOfdm OSIRIP PPPRadius Smtp RSASnmp SohoTCP SsidTCP/IP TftpUSB URLUTP VlanWisp WDSWlan WPA802.11 Yagi antennaTechnical Support