Seagate ST9160414ASG, ST980414ASG Reliability, Agency certification, Free Fall Protection feature

Page 23

2.13

Reliability

 

 

 

Measurement type

Specification

 

 

Nonrecoverable read errors

1 per 1014 bits read, max.

Annualized Failure Rate (AFR)

0.48%

 

 

Load/Unload (U/UL)

 

25°C, 50% relative humidity

600,000 software-controlled power on/off cycles

 

 

50,000 hard power on/off cycles

32°C, 80% relative humidity

600,000 software-controlled power on/off cycles

5°C, 80% relative humidity

50,000 hard power on/off cycles

5°C, 10% relative humidity

 

55°C, 16% relative humidity

 

 

 

 

Warranty

 

5 years on distribution units.

 

 

Important: When returning a drive for warranty support, if possible, you should

 

 

provide the valid ATA Master password, or return the drive in the Security Erased

 

 

state with the User Data Area accessible.

 

 

If these recommendations are not followed, Seagate cannot access the drive to

 

 

perform failure analysis to verify your warranty claim.

 

 

To determine the warranty for a specific drive, use a web browser to access the

 

 

following web page:

 

 

www.seagate.com/support/service/

 

 

From this page, click on the “Verify Your Warranty” link. You will be asked to pro-

 

 

vide the drive serial number, model number (or part number) and country of pur-

 

 

chase. The system will display the warranty information for your drive.

 

 

 

2.13.1Free Fall Protection feature

The Free Fall Protection feature provides enhanced data protection against shock events that may occur while the drive is operating. This feature is designed to decrease the likelihood of data loss by detecting a free fall event and unloading the actuator before a shock takes place in falls of >8 inches (nominal). The drive uses a 0G sensor mounted on the printed circuit board assembly (PCBA) to sense this event.

To enable the Free Fall Protection feature on ST9320424ASG, ST9250424ASG, ST9160414ASG, ST9120414ASG, and ST980414ASG models, use Set Features command 41h. To disable this feature, use Set Features command C1h.

Information about Free Fall Events that have occurred is available through SMART Attribute FEh.

Note. The Free Fall Protection feature is provided only on ST9320424ASG, ST9250424ASG, ST9160414ASG, ST9120414ASG, and ST980414ASG models.

2.14Agency certification

2.14.1Safety certification

The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950 as tested by TUV North America.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

17

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Momentus 7200 FDE.1 Sata Page Contents Compatibility summary Seagate Technology support servicesSerial ATA interface List of Figures Page System requirements IntroductionFDE benefits Security feature matrixFDE drive feature list About Momentus 7200 FDE.1 Sata disc drivesDrive state upon shipment Momentus 7200 FDE.1 Sata Product Manual, Rev. a Specification summary table Drive specificationsSystem will display the warranty information for your drive Cylinders Read/write heads Sectors per track 16,383 Default logical geometryLBA mode Formatted capacityRecording and interface technology Physical characteristicsDrive specification Physical organizationTime to ready Typical Max @ 25C Seek timeStart/stop times Typical seek times msec ReadPower specifications Voltage tolerance Typical current profileConducted noise Idle mode Power-management modesPower management modes Active modeEnvironmental specifications Vibration ShockOperating shock Nonoperating shockIdle Performance seek AcousticsElectromagnetic immunity Test for Prominent Discrete Tones PDTsPerformance Reference Test Description Level Standard Reliability Free Fall Protection featureSafety certification Measurement type SpecificationFCC verification Electromagnetic compatibilityKorean RRL Australian C-Tick N176Page China Restriction of Hazardous Substances RoHS Directive Environmental protectionEuropean Union Restriction of Hazardous Substances RoHS Handling and static-discharge precautions Configuring and mounting the driveSerial ATA cables and connectors Configuring the driveDrive mounting Mounting dimensionsMomentus 7200 FDE.1 Sata drive label example Drive integrationConsumer usage Security Erase--ATA security commandsDrive installation Secure Erase procedurePage Serial ATA interface Pin Function Definition Serial ATA connector pin definitionsSignal ATA Security Erase Unit bits Word ContentATA Security policy exceptions Ident Value BIT set Bit Description DriveTrust Mode supportDriveTrust Identify Full Disc Encryption Identify Full Disc Encryption supportNormal Commands Supported ATA commandsSupported commands Read LOG EXT SET MAX Freeze Lock ATA Security API DriveTrust Security API Code Command Locked Unlocked FrozenWord Description Value Identify Device commandXxxxH Description if bit is set to Bit Word Bit Word Ultra DMA mode 0 is supportedBit Word Set Features command0CH Set Features command valuesCode in features register A.R.T. command 7 S.M.A.R.T. commandsM.A.R.T. commands Momentus 7200 FDE.1 Sata Product Manual, Rev. a Tested Bios versions with Windows XP SP2 Installation considerationsSystem Compatibility using WIndows XP SP2 Bios versions tested in ATA Security modeAMD Phoenix Award Dell AMI VVPGI635 DriveTrust compatibility verification DriveTrust compatibility BiosTian YI F30A ATA Operating system versions tested Manufacturer Version/Release Compatibility test configurationsSupported operating systems Technical Support InternetPresales Support Data Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index ITE TPI Momentus 7200 FDE.1 Sata Product Manual, Rev. a Page Seagate Technology LLC
Top Page Image Contents