Seagate ST9500431SS Drive Self Test DST, DST failure definition, Implementation, Invoking DST

Page 26

6.2.6Drive Self Test (DST)

Drive Self Test (DST) is a technology designed to recognize drive fault conditions that qualify the drive as a failed unit. DST validates the functionality of the drive at a system level.

There are two test coverage options implemented in DST:

1.Extended test

2.Short test

The most thorough option is the extended test that performs various tests on the drive and scans every logical block address (LBA) of the drive. The short test is time-restricted and limited in length—it does not scan the entire media surface, but does some fundamental tests and scans portions of the media.

If DST encounters an error during either of these tests, it reports a fault condition. If the drive fails the test, remove it from service and return it to Seagate for service.

6.2.6.1DST failure definition

The drive will present a “diagnostic failed” condition through the self-tests results value of the diagnostic log page if a functional failure is encountered during DST. The channel and servo parameters are not modified to test the drive more stringently, and the number of retries are not reduced. All retries and recovery processes are enabled during the test. If data is recoverable, no failure condition will be reported regardless of the number of retries required to recover the data.

The following conditions are considered DST failure conditions:

•Seek error after retries are exhausted

•Track-follow error after retries are exhausted

•Read error after retries are exhausted

•Write error after retries are exhausted

Recovered errors will not be reported as diagnostic failures.

6.2.6.2Implementation

This section provides all of the information necessary to implement the DST function on this drive.

6.2.6.2.1State of the drive prior to testing

The drive must be in a ready state before issuing the Send Diagnostic command. There are multiple reasons why a drive may not be ready, some of which are valid conditions, and not errors. For example, a drive may be in process of doing a format, or another DST. It is the responsibility of the host application to determine the “not ready” cause.

While not technically part of DST, a Not Ready condition also qualifies the drive to be returned to Seagate as a failed drive.

A Drive Not Ready condition is reported by the drive under the following conditions:

•Motor will not spin

•Motor will not lock to speed

•Servo will not lock on track

•Drive cannot read configuration tables from the disc

In these conditions, the drive responds to a Test Unit Ready command with an 02/04/00 or 02/04/03 code.

6.2.6.2.2Invoking DST

To invoke DST, submit the Send Diagnostic command with the appropriate Function Code (001b for the short test or 010b for the extended test) in bytes 1, bits 5, 6, and 7.

18

Constellation SAS Product Manual, Rev. E

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Standard Model Self-Encrypting Drive Model ST9500430SSST9500431SSST9500432SS SED Fips 140-2 ModelRevision history Contents About Fips About self-encrypting drives Defect and error managementInstallation Interface requirementsPower Constellation SAS Product Manual, Rev. E List of Figures GB model current profilesConstellation SAS Product Manual, Rev. E Seagate Technology support services Seagate Online Support and ServicesScope Electromagnetic compatibility Applicable standards and reference documentationStandards Electromagnetic susceptibilityAustralian C-Tick Electromagnetic complianceElectromagnetic compliance for the European Union Korean KCCReference documents European Union Restriction of Hazardous Substances RoHSGeneral description Standard features Media descriptionFormatted capacities PerformanceReliability Programmable drive capacityFactory-installed options Seek performance characteristics Performance characteristicsInternal drive characteristics Access timeGeneral performance characteristics Start/stop timePrefetch/multi-segmented cache control Cache operationCaching write data Prefetch operationRecoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T Reporting controlThermal monitor Temperature Log Page 0Dh Parameter Code DescriptionPredictive failures DST failure definition State of the drive prior to testingDrive Self Test DST ImplementationExtended test Function Code 010b Short and extended testsShort test Function Code 001b Log page entriesProduct repair and return information Product warrantyShipping PowerChoice modes Physical/electrical specificationsPowerChoiceTM power management AC power requirements DC power requirementsPage Conducted noise immunity General DC power requirement notesPower sequencing Current profiles GB model current profilesPower dissipation ST9500430SS, ST9500431SS and ST9500432SS in 3 Gbit operationST9500430SS, ST9500431SS and ST9500432SS in 6 Gbit operation Temperature a. Operating Environmental limitsShock and vibration Relative humidityEffective altitude sea level a. Operating ShockPage Recommended mounting Corrosive environment Air cleanlinessVibration a. Operating-normal Acoustics Mechanical specifications Mounting configuration dimensionsLevel 2 security About FipsPurpose About self-encrypting drives Controlled accessAdmin SP Data encryptionDrive locking Default passwordRandom number generator RNG Data bandsSupported commands Authenticated firmware downloadPower requirements Cryptographic eraseDrive error recovery procedures Defect and error managementDrive internal defects/errors SAS system errors Deferred Auto-Reallocation Background Media ScanMedia Pre-Scan Idle Read After Write Installation Drive orientationCooling Air flowDrive mounting GroundingSAS features Interface requirementsDual port support Scsi commands supported Supported commandsSupported commands Supported commands Supported commands Constellation inquiry data Mode Sense dataInquiry data Page Mode Data Header Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features SAS physical interface Datum B Section C C Section a a Electrical description Physical characteristicsConnector requirements Pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutDifferential signals SAS-2 Specification ComplianceLED drive signal General interface characteristicsConstellation SAS Product Manual, Rev. E Index NumericsKCC Msid Mtbf See also cooling Page Constellation SAS Product Manual, Rev. E Page Seagate Technology LLC
Top Page Image Contents