Seagate Official Manual for Computer Drives: PowerChoice Reporting for Enhanced Performance

Page 30

7.1.1PowerChoice reporting methods

PowerChoiceTM provides these reporting methods for tracking purposes:

Request Sense command reports

•Current power condition

•Method of entry

Note. Processing the Request Sense command does not impact the drive’s power save state.

Mode Sense command reports (mode page 0x1A)

•Idle conditions enabled / disabled

•Idle condition timer values (100msec increments) (default, saved, current, changeable)

Power Condition Vital Product Data (VPD) Page (VPD page 0x8A)

•Supported power conditions

•Typical recovery time from power conditions (1msec increments)

Start/Stop Cycle Counter Log Page reports (log page 0x0E)

• Specified and accumulated Start/Stops and Load/Unload cycles

Power Condition Transitions Log Page reports (log page 0x1A, subpage 0x00)

• Accumulated transitions to Active, Idle1, Idle2, Idle3, Standby2, Standby

7.2AC power requirements

None.

7.3DC power requirements

The voltage and current requirements for a single drive are shown below. Values indicated apply at the drive connector.

The standard drive models and the SED drive models have identical hardware, however the security and encryption portion of the drive controller ASIC is enabled and functional in the SED models. This represents a small additional drain on the 5V supply of about 30mA and a commensurate increase of about 150mW in power consumption. There is no additional drain on the 12V supply.

22	Constellation SAS Product Manual, Rev. E

Image 30

Contents Standard Model Self-Encrypting Drive Model ST9500430SSST9500431SSST9500432SS SED Fips 140-2 ModelRevision history Contents About Fips About self-encrypting drives Defect and error managementInstallation Interface requirementsPower Constellation SAS Product Manual, Rev. E List of Figures GB model current profilesConstellation SAS Product Manual, Rev. E Seagate Technology support services Seagate Online Support and ServicesScope Electromagnetic compatibility Applicable standards and reference documentationStandards Electromagnetic susceptibilityAustralian C-Tick Electromagnetic complianceElectromagnetic compliance for the European Union Korean KCCReference documents European Union Restriction of Hazardous Substances RoHSGeneral description Standard features Media descriptionFormatted capacities PerformanceReliability Programmable drive capacityFactory-installed options Seek performance characteristics Performance characteristicsInternal drive characteristics Access timeGeneral performance characteristics Start/stop timePrefetch/multi-segmented cache control Cache operationCaching write data Prefetch operationRecoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T Reporting controlTemperature Log Page 0Dh Parameter Code Description Predictive failuresThermal monitor DST failure definition State of the drive prior to testingDrive Self Test DST ImplementationExtended test Function Code 010b Short and extended testsShort test Function Code 001b Log page entriesProduct warranty ShippingProduct repair and return information Physical/electrical specifications PowerChoiceTM power managementPowerChoice modes AC power requirements DC power requirementsPage General DC power requirement notes Power sequencingConducted noise immunity Current profiles GB model current profilesPower dissipation ST9500430SS, ST9500431SS and ST9500432SS in 3 Gbit operationST9500430SS, ST9500431SS and ST9500432SS in 6 Gbit operation Temperature a. Operating Environmental limitsShock and vibration Relative humidityEffective altitude sea level a. Operating ShockPage Recommended mounting Air cleanliness Vibration a. Operating-normalCorrosive environment Acoustics Mechanical specifications Mounting configuration dimensionsAbout Fips PurposeLevel 2 security About self-encrypting drives Controlled accessAdmin SP Data encryptionDrive locking Default passwordRandom number generator RNG Data bandsSupported commands Authenticated firmware downloadPower requirements Cryptographic eraseDefect and error management Drive internal defects/errorsDrive error recovery procedures SAS system errors Background Media Scan Media Pre-ScanDeferred Auto-Reallocation Idle Read After Write Installation Drive orientationCooling Air flowDrive mounting GroundingSAS features Interface requirementsDual port support Scsi commands supported Supported commandsSupported commands Supported commands Supported commands Mode Sense data Inquiry dataConstellation inquiry data Page Mode Data Header Miscellaneous operating features and conditions Miscellaneous featuresMiscellaneous status SAS physical interface Datum B Section C C Section a a Electrical description Physical characteristicsConnector requirements Pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutDifferential signals SAS-2 Specification ComplianceLED drive signal General interface characteristicsConstellation SAS Product Manual, Rev. E Index NumericsKCC Msid Mtbf See also cooling Page Constellation SAS Product Manual, Rev. E Page Seagate Technology LLC