Seagate ST680712DE China Restriction of Hazardous Substances RoHS Directive, FCC verification

Page 24

2.12.4China Restriction of Hazardous Substances (RoHS) Directive

2.12.4中国限制危险物品的指令

This product has an Environmental Protection Use Period (EPUP) of 20 years. The following table contains information mandated by China's "Marking Requirements for Control of Pollution Caused by Electronic Information Products" Standard.

"O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower than the threshold defined by the China RoHS MCV Standard.

O"表示该部件(于同类物品程度上)所含的危险和有毒物质低于中国RoHS MCV标准所定义的门槛值。

"X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over the threshold defined by the China RoHS MCV Standard.

X "表示该部件(于同类物品程度上)所含的危险和有毒物质超出中国RoHS MCV标准所定义的门槛值。

2.12.5FCC verification

These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an external device). As such, each drive is considered to be a subassembly even when it is individually mar- keted to the customer. As a subassembly, no Federal Communications Commission verification or certification of the device is required.

Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is likely to result in interference to radio and television reception.

Radio and television interference. This equipment generates and uses radio frequency energy and if not installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception.

This equipment is designed to provide reasonable protection against such interference in a residential installa- tion. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television, which can be determined by turning the equipment on and off, you are encouraged to try one or more of the following corrective measures:

Reorient the receiving antenna.

Move the device to one side or the other of the radio or TV.

Move the device farther away from the radio or TV.

Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.

18

ST1.3 Series Product Manual, Rev. C

Image 24
Contents ST1.3 Series Rev. CRevision status summary sheet Contents ST1.3 Series Product Manual, Rev. C List of Figures ST1.3 Series Product Manual, Rev. C ST1.3 Series IDE interface ZIF connector disc drive IntroductionHandling precautions DisclaimerDrive care Drive specifications Power, access times and acousticsSpecifications Gs 0 to peak, 10-500 Hz @ 0.5 oct/min sweep rate Default logical geometry LBA modeFormatted capacity Model Cylinders Read/write heads Sectors per trackPhysical characteristics Technology SpecificationRecording and interface technology Time to readyPower specifications DC power Typical current profileConducted noise Voltage tolerance Voltage tolerance including noisePower-management modes Active modePerformance idle mode Standby/Sleep modeEnvironmental specifications Shock Operating shockNonoperating shock VibrationOperating sweep sine vibration Operating random vibrationOperating random vibration profile Nonoperating sweep sine vibrationNonoperating random vibration Nonoperating random vibration profileCorrosive environment Acoustics Electromagnetic immunityDrive level acoustics Electromagnetic immunityMeasurement type Specification ReliabilitySafety certification Agency certificationElectromagnetic compatibility Korean RRLChina Restriction of Hazardous Substances RoHS Directive FCC verificationPage ST1.3 Series Product Manual, Rev. C Configuring and mounting the drive Handling and static discharge precautionsSeries Proper Handling example Drive installation ST1.3 Series Product Manual, Rev. C Mounting considerations ST1.3 Series Area for Protective MountingConnector interface signals and connector pins Way ZIF IDE interface connector signalsInterface description Iord Supported ATA commands Supported commands Identify Device command Word ATA specification ValueXxA5H Description if bit is set to Bit Set Features command Features register valuesFeature Description ST1.3 Series Product Manual, Rev. C Seagate Technology support services InternetPresales Support Technical SupportWarranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Publication feedback survey ST1.3 Series Product Manual, Rev. C Index Page Page ST1.3 Series Product Manual, Rev. C Page Seagate Technology LLC