Western Telematic IPS-800CE-D16, IPS-1600CE-D16 manual Restoring Saved Parameters

Page 48

IPS-800CE-D16 & IPS-1600CE-D16 - User’s Guide

7.2. Restoring Saved Parameters

This Section describes the procedure for using your communications program to send saved parameters to the IPS.

Note: Parameters saved to an ASCII ﬁle can only be restored via the Text Interface. This procedure cannot be performed via the Web Browser Interface.

1.Start your communications program and access the IPS command mode via the Text Interface as described in Section 5.2.2.

2.If the Password Prompt is displayed, key in your System Level Password and press [Enter].

3.Conﬁgure your communications program to upload an ASCII text ﬁle.

4.Upload the ﬁle with the saved parameters. If necessary, key in the ﬁle name and directory path.

5.When the upload is complete, make certain to terminate the communications program’s upload mode.

Note:

•The current On/Off status of each IPS plug will not be saved or restored.

•When the conﬁguration ﬁle is sent to the IPS via telnet, the unit’s IP Address, Subnet Mask, and Gateway Address will not be changed until after you exit from command mode.

At this point, saved parameters should have been restored to the IPS unit. Check the Plug Status Screen, General Parameters Menu, Plug Parameters Menu and Network Parameters Menu to make certain that saved parameters have been accurately restored.

7-2

Image 48

Contents IPS-800CE-D16 IPS-1600CE-D16 User’s GuidePage Installation Instructions EMC, Safety, and R&TTE Directive Compliance Table of Contents List of Figures Introduction IPS-800CE-D16 and IPS-1600CE-D16 Units Typographic ConventionsUnit Description IPS-800CE-D16 Back Panel 8-Plug UnitIPS-800CE-D16 & IPS-1600CE-D16 User’s Guide Hardware Installation Apply Power to the IPSQuick Start Communicating with the IPS Connect your PC to the IPSText Interface Text Interface Type /X and press Enter Installation Power Supply ConnectionInstalling the Cable Keepers Connection to Switched Outlets Serial COM / RS232 Port ConnectionConnecting the Network Cable Connecting a Local PCConnecting an External Modem IPS-800CE-D16 & IPS-1600CE-D16 User’s Guide Configuration System Mode and User ModeAccessing the Web Browser Interface Plug Status Screen Web Browser Interface IPS-800CE-D16 ShownAccessing the Text Interface $ telnet 192.168.168.168 Enter Configuration Menus General Parameters Menus General Parameters Menu Web Browser InterfaceGeneral Parameters Menu Text Interface IPS-800CE-D16 & IPS-1600CE-D16 User’s Guide Serial Parameters Menu Serial ParametersIPS-800CE-D16 & IPS-1600CE-D16 User’s Guide Plug Parameters Menus Plug #1 ParametersPlug Passwords and Co-Location Features Reboot Cycles Network Parameters Menu Web Browser Interface Network Parameters Menus IP Security Feature Conﬁ guration Telnet Parameters Menus 12 Telnet Parameters Menu Web Browser InterfaceWeb Server Parameters Menus 14 Web Server Parameters Menu Web Browser InterfaceSave Configuration Parameters Operation Operation via the Web Browser InterfacePlug Status Screen Web Browser Interface Plug Status Menu Web Browser Interface IPS-800CE-D16 Shown Operation via the Text Interface Plug Status Screen Text InterfaceSwitching and Reboot Commands Text Interface IPS Help Screen Text InterfaceBoot 1 or /BO Atmswtch Logging Out of Command Mode Applying Commands to Several Plugs Text InterfaceAutomated Mode Manual Operation Saving and Restoring Configuration Parameters Sending Parameters to a FileRestoring Saved Parameters Upgrading the IPS Firmware IPS-800CE-D16 & IPS-1600CE-D16 User’s Guide Interface Description Serial COM / RS232 Port InterfaceApx-1 Specifications Apx-2Customer Service Apx-3Trademark and Copyright Information Apx-4Index Index-1Index-2 IPS-800/1600-D20 Series User’s GuidePage Sterling Irvine California 949 586-9950 Toll Free