Tut Systems SMS2000 manual System Administration, Configuration E-Mail Settings

Page 25

System Administration

Chapter4 - System Administration

This chapter describes the system administration activities and commands, including:

•Configuration E-Mail Settings

•Configuration and System File Tools

•Configuring SMTP

•Configuring NTP

•Configuring SNMP Polling

•Connectivity and Testing

•System Tools

•Event Tracking

•System Administration Tools

•Troubleshooting Tools

•Subscriber Connectivity Commands

•Upgrades

Configuration E-Mail Settings

Setting the Default Configuration E-mail

Each time you save a new configuration, the SMS2000 can automatically send an e-mail with the new configuration to a specified recipient. The set config-mailcommand allows you to specify the recipient.

Note: The SMTP server must be the DNS name or IP address of the destination mail server. If the IP address is not provided, the server name in the e-mail address is used, which is normally not the desired behavior.

To configure the SMS2000 to send its configuration file to a specified e-mail address each time the configuration is saved, use this command:

set config-mailrecipient@SMTPserver [SMTPserver]

For example, to configure the SMS2000 to send an e-mail with the new configuration file attached to ted@smith.com, using smith.com as the e-mail server, type:

sms2000% set config-mail ted@smith.com mail.smith.com

TUT Systems, Inc

Page 25 of 104

P/N 220-06288-20

Image 25

Contents TUT Systems SMS2000 User Guide SMS2000 User’s Guide SMSUser’s Guide Contents Configuring NTP Configuring SmtpConfiguring Snmp Polling Connectivity and TestingAuthentication Authentication Configuring the Command ServerAuthentication with Radius AuthorizationConfiguring Radius Using Rule PrioritiesGroups SMS2000 RulesWeb Proxy Settings Using Both Radius and OCS AuthenticationSMS2000 Troubleshooting Procedures SMS2000 Status Attributes and StatisticsList of Tables Radius Attributes in Access-Accept PacketsList of Figures Audience PrefaceDocumentation available for this Release Related DocumentationIntroduction Subscriber Management FeaturesIntroduction Subscriber Management Components Subscriber Management ComponentsOCS SMS2000Introduction User Interface Getting StartedFor example restore config web original-confi g Accessing Help for CommandsIfconfig portnumber ipaddress /masklen Style ConventionsCursor Motion Keystrokes Cursor MovementClick Configure Initial ConfigurationEstablishing a Connection with the SMS2000 Establishing a Connection Via a Serial InterfaceEstablishing a Connection Via Telnet Initial Configuration Changing Your Password Initial ConfigurationSetting the Quick Configuration Disabling Authentication Setting the HostnameSaving the Configuration Verifying the Configuration Rebooting the SystemReboot Configuration E-Mail Settings System AdministrationSetting the Default Configuration E-mail Set config-mailrecipient@SMTPserver SMTPserverMailing the Current Configuration Configuration and System File ToolsDeleting the Configuration E-mail Committing Configuration ChangesDisabling Automatic Configuration Changes Automatically Committing Configuration ChangesCommit auto Commit noautoLoading a Configuration File Saving a ConfigurationRestoring a Previous Configuration Restoring the Default Configuration Configuring SmtpSetting the Smtp Server Deleting the Smtp ServerSetting the Smtp ID Configuring NTPSetting the Timezone Set smtpid on offConfiguring the NTP server Configuring Snmp PollingSetting the Time Enabling Snmp PollingDisabling Snmp Polling Testing to See if Snmp Polling will WorkSnmp-pollmacaddress Testing Connectivity Connectivity and TestingSetting Specialized System Options System ToolsDefining Ports Setting and Deleting Static PortsLeftrighthelp ? Port-definition mixed tut vlanSetting the Syslog Server Disconnecting a Session on a PortEvent Tracking Displaying Log MessagesDisplaying Version Information System Administration ToolsExiting the Management Session Displaying Control Keys Changing a PasswordPasswd KeysSnmp Agent Snmp ManagementSnmp System Contact Snmp System LocationSnmp Trap Recipient Snmp CommunitySystem Information Tools Troubleshooting ToolsSMS2000% snmp delete trap-recipient Show snmp trap-recipientUpgrades Subscriber Connectivity CommandsSetting the ARP Failure Limit Setting the ARP Polling PeriodArchiving SMS2000 Firmware and distributing it from a Server Upgrading from Tut Systems’ WebsiteReturning to an Older Firmware Version Verifying a Successful UpgradeLoading Another Image System Administration Authentication AuthenticationSetting the Command Server for OCS Interaction Configuring the Command ServerDeleting the Command Server Adding the OCS as the Authentication ServerTesting Authentication Deleting an Authentication ServerAuth add web url secret secret cmd-serv Auth onBypassing Authentication Setting the Authentication IntervalAuth off forcedweb authokurl blockall Auth interval minutes offHttp Request Throttle Setting the Http Request ThrottleAllow-Nets Deleting the Http Request ThrottleSet allow-netipaddress netmask dns-name Setting an Allow-NetAutomatic Redirection URLs Setting the Automatic Redirection URLDeleting an Allow-Net Set authok urlDeleting the authok Authentication with RadiusAdding a Radius Server Delete authokSyntax Description CommandDefault retrans-primary-only is DefaultUsage Guidelines Example Set nas-port-type integer Set NAS port type parameterSet nas-port-type Configuring a Radius SSL Back Channel Testing Authentication on the Radius ServerShow status radius Show status radius ExampleAuthorization AuthorizationAuthorization Server FunctionalityAccounting AccountingSending Accounting Messages to a Syslog Server Configuring Accounting Parameters Radius Accounting ConfigurationSending Accounting Messages to a Radius Server Deleting a Radius Accounting ServerProvisioning ProvisioningBilling BillingGroups Service Creation Using Groups and RulesAdding a Group Group add groupname noinherit inherit groupnameSubscribers that Cannot Support Authentication Setting the Active Group ContextSetting Maximum Users Per Port Deleting a GroupAdding a Rule SMS2000 RulesDeleting a Rule Set rule rulename groupname priority rulestringIP Address Rule Expression ComponentsMAC Address Ip=ipaddress ,netmaskVlan=vlanida-vlanidb Not OperatorTut=ipaddress-linenum*-portnum Or Operator OperatorParenthesis Expression and expressionUsing Rule Priorities IP Addressing IP AddressingPlug and Play With NAT Dhcp Pools Static Routable AddressesIP Multicasting Static Non-Routable AddressesIptype default NAT static Dhcp 1to1 1to1Unique Configuring IP TypesUnderstanding 1to1 and 1to1 Unique IP Types Deleting a Configured Source-Net Setting a Source-NetSource-Nets Set source-netstartaddress endaddress subnet-maskCreating Dhcp Pools Setting the DNS Server AddressRemoving a Dhcp Assignment Dhcp-server release macaddressDeleting the DNS Server Address Static RoutesAdding Routes Set dns add ipaddressPrinting Setting up the LPR HostSet lpr hostname off queuename maxpages maxbytes Configuring Radius Using SMS2000 with a Radius ServerObtaining the Radius Server Software Adding the SMS2000 as a Client on the Radius Server Configuring Service ParametersAdding Users to the Radius Server Radius Ports Using Real IP AddressesSMS2000 NAS File SMS2000 Status Attributes and StatisticsRadius Attributes Sent in Accounting Messages Radius Attributes Sent In Access Request Packets Using Both Radius and OCS AuthenticationRadius Attributes Received in Access- Accept Packets Deleting Traffic Shaping Setting Traffic ShapingShape xbps/rbps Shape xbps/rbps deleteSMS2000 and Property Management Systems PMS Setting the PMS ServerTTY ACK-NAK ENQ-ACK-NAK Protocol ModesENQ-ACK-NAK Mode Loading and Deleting Customized Web Pages Customizing SMS2000 Web Authentication with RadiusFiles For Groups Loading Web Pages or FilesPath Components Load web url defaultsImage Links Upgrading Customizing Web PagesDeleting Web Pages or Files Preserving the Web FormWeb Page Redirection Size For Web Pages and External LinksViewing Customizations Active Page ComponentsReference Web Proxy Settings Configuring Web Proxy SettingsSetting the Wpad Curl Setting the Wpad TimeoutWeb Proxy Server Delete proxy-ports port Set proxy-ports portShow proxy-ports SMS2000 Troubleshooting Procedures SMS2000 TroubleshootingMultiple frames opened Snmp PollingBrowser Unable to do credit cardLine Verify OCS screens offRadius Attributes in Access-Accept Packets Appendix a Radius Access-Accept Dictionary FileAppendix Appendix TUT Systems, Inc 100 Technical Support Appendix B Technical Assistance and Customer SupportInternet Telephone Equipment Return and RepairHardware Limited Warranty Appendix C SMS2000 Limited WarrantyLimitations of Warranty Exclusive RemediesTut Systems, Inc., Customer Service Department Electrical Safety AdvisoryAssistance FCC Radio Frequency Interference StatementTUT Systems, Inc 104