Tut Systems SMS2000 manual Configuration and System File Tools, Mailing the Current Configuration

Page 26

System Administration

Mailing the Current Configuration

The config-mailcommand mails the current configuration to the address specified. The SMS2000 uses the SMTP (Simple Mail Transfer Protocol) server specified by the e-mail address or SMTP-server command line parameter. If you enter config-mailwith no parameters, the SMS2000 uses the server last configured with set config-mail.

Once connected, the SMS2000 sends an e-mail message to the specified (or default - if none is entered) recipient. The message includes a brief explanation of why it was sent with the SMS2000 configuration file attached.

The manager can store the configuration file on an FTP or HTTP server, and later recover it using the load config command.

To temporarily override the default e-mail configuration settings and mail the SMS2000 configuration to the specified e-mail address using the given local email server, use this command:

config-mail[recipient_e-mail [SMTP_server]]

For example, to override the default configuration e-mail settings and send the config e- mail to billy@chung.com, using chung.com as a valid e-mail server that accepts e-mail directly from the SMS2000, type:

sms2000% config-mail billy@chung.com mail.chung.com

Deleting the Configuration E-mail

To delete the configured e-mail address and mail server to be notified when saving the system configuration, use this command:

delete config-mail

For example, to disable e-mail notification of configuration changes, use this command:

sms2000% delete config-mail

Configuration and System File Tools

Committing Configuration Changes

To immediately commit configuration changes to the running system and synchronize the running system with the state of the configuration, use this command:

commit

For example, to immediately commit a configuration change, type:

sms2000% commit

TUT Systems, Inc

Page 26 of 104

P/N 220-06288-20

Image 26

Contents TUT Systems SMS2000 User Guide SMS2000 User’s Guide SMSUser’s Guide Contents Configuring Snmp Polling Configuring SmtpConfiguring NTP Connectivity and TestingAuthentication with Radius Authentication Configuring the Command ServerAuthentication AuthorizationGroups Using Rule PrioritiesConfiguring Radius SMS2000 RulesSMS2000 Troubleshooting Procedures Using Both Radius and OCS AuthenticationWeb Proxy Settings SMS2000 Status Attributes and StatisticsList of Figures Radius Attributes in Access-Accept PacketsList of Tables Documentation available for this Release PrefaceAudience Related DocumentationSubscriber Management Features IntroductionIntroduction Subscriber Management Components Subscriber Management ComponentsSMS2000 OCSIntroduction Getting Started User InterfaceIfconfig portnumber ipaddress /masklen Accessing Help for CommandsFor example restore config web original-confi g Style ConventionsCursor Movement Cursor Motion KeystrokesEstablishing a Connection with the SMS2000 Initial ConfigurationClick Configure Establishing a Connection Via a Serial InterfaceEstablishing a Connection Via Telnet Initial Configuration Setting the Quick Configuration Initial ConfigurationChanging Your Password Saving the Configuration Setting the Hostname Disabling Authentication Reboot Rebooting the SystemVerifying the Configuration Setting the Default Configuration E-mail System AdministrationConfiguration E-Mail Settings Set config-mailrecipient@SMTPserver SMTPserverDeleting the Configuration E-mail Configuration and System File ToolsMailing the Current Configuration Committing Configuration ChangesCommit auto Automatically Committing Configuration ChangesDisabling Automatic Configuration Changes Commit noautoRestoring a Previous Configuration Saving a ConfigurationLoading a Configuration File Setting the Smtp Server Configuring SmtpRestoring the Default Configuration Deleting the Smtp ServerSetting the Timezone Configuring NTPSetting the Smtp ID Set smtpid on offSetting the Time Configuring Snmp PollingConfiguring the NTP server Enabling Snmp PollingSnmp-pollmacaddress Testing to See if Snmp Polling will WorkDisabling Snmp Polling Setting Specialized System Options Connectivity and TestingTesting Connectivity System ToolsLeftrighthelp ? Setting and Deleting Static PortsDefining Ports Port-definition mixed tut vlanEvent Tracking Disconnecting a Session on a PortSetting the Syslog Server Displaying Log MessagesExiting the Management Session System Administration ToolsDisplaying Version Information Passwd Changing a PasswordDisplaying Control Keys KeysSnmp System Contact Snmp ManagementSnmp Agent Snmp System LocationSnmp Community Snmp Trap RecipientSMS2000% snmp delete trap-recipient Troubleshooting ToolsSystem Information Tools Show snmp trap-recipientSetting the ARP Failure Limit Subscriber Connectivity CommandsUpgrades Setting the ARP Polling PeriodUpgrading from Tut Systems’ Website Archiving SMS2000 Firmware and distributing it from a ServerLoading Another Image Verifying a Successful UpgradeReturning to an Older Firmware Version System Administration Authentication AuthenticationDeleting the Command Server Configuring the Command ServerSetting the Command Server for OCS Interaction Adding the OCS as the Authentication ServerAuth add web url secret secret cmd-serv Deleting an Authentication ServerTesting Authentication Auth onAuth off forcedweb authokurl blockall Setting the Authentication IntervalBypassing Authentication Auth interval minutes offAllow-Nets Setting the Http Request ThrottleHttp Request Throttle Deleting the Http Request ThrottleSetting an Allow-Net Set allow-netipaddress netmask dns-nameDeleting an Allow-Net Setting the Automatic Redirection URLAutomatic Redirection URLs Set authok urlAdding a Radius Server Authentication with RadiusDeleting the authok Delete authokCommand Syntax DescriptionUsage Guidelines Example DefaultDefault retrans-primary-only is Set nas-port-type Set NAS port type parameterSet nas-port-type integer Show status radius Testing Authentication on the Radius ServerConfiguring a Radius SSL Back Channel Show status radius ExampleAuthorization AuthorizationAuthorization Server FunctionalitySending Accounting Messages to a Syslog Server AccountingAccounting Sending Accounting Messages to a Radius Server Radius Accounting ConfigurationConfiguring Accounting Parameters Deleting a Radius Accounting ServerProvisioning ProvisioningBilling BillingAdding a Group Service Creation Using Groups and RulesGroups Group add groupname noinherit inherit groupnameSetting Maximum Users Per Port Setting the Active Group ContextSubscribers that Cannot Support Authentication Deleting a GroupDeleting a Rule SMS2000 RulesAdding a Rule Set rule rulename groupname priority rulestringMAC Address Rule Expression ComponentsIP Address Ip=ipaddress ,netmaskTut=ipaddress-linenum*-portnum Not OperatorVlan=vlanida-vlanidb Parenthesis OperatorOr Operator Expression and expressionUsing Rule Priorities Plug and Play With NAT IP AddressingIP Addressing Static Routable Addresses Dhcp PoolsStatic Non-Routable Addresses IP MulticastingUnderstanding 1to1 and 1to1 Unique IP Types Configuring IP TypesIptype default NAT static Dhcp 1to1 1to1Unique Source-Nets Setting a Source-NetDeleting a Configured Source-Net Set source-netstartaddress endaddress subnet-maskRemoving a Dhcp Assignment Setting the DNS Server AddressCreating Dhcp Pools Dhcp-server release macaddressAdding Routes Static RoutesDeleting the DNS Server Address Set dns add ipaddressSet lpr hostname off queuename maxpages maxbytes Setting up the LPR HostPrinting Obtaining the Radius Server Software Using SMS2000 with a Radius ServerConfiguring Radius Adding Users to the Radius Server Configuring Service ParametersAdding the SMS2000 as a Client on the Radius Server Using Real IP Addresses Radius PortsRadius Attributes Sent in Accounting Messages SMS2000 Status Attributes and StatisticsSMS2000 NAS File Radius Attributes Received in Access- Accept Packets Using Both Radius and OCS AuthenticationRadius Attributes Sent In Access Request Packets Shape xbps/rbps Setting Traffic ShapingDeleting Traffic Shaping Shape xbps/rbps deleteSetting the PMS Server SMS2000 and Property Management Systems PMSProtocol Modes TTY ACK-NAK ENQ-ACK-NAKENQ-ACK-NAK Mode Files For Groups Customizing SMS2000 Web Authentication with RadiusLoading and Deleting Customized Web Pages Loading Web Pages or FilesImage Links Load web url defaultsPath Components Deleting Web Pages or Files Customizing Web PagesUpgrading Preserving the Web FormSize For Web Pages and External Links Web Page RedirectionReference Active Page ComponentsViewing Customizations Setting the Wpad Curl Configuring Web Proxy SettingsWeb Proxy Settings Setting the Wpad TimeoutWeb Proxy Server Show proxy-ports Set proxy-ports portDelete proxy-ports port SMS2000 Troubleshooting SMS2000 Troubleshooting ProceduresBrowser Snmp PollingMultiple frames opened Unable to do credit cardVerify OCS screens off LineAppendix a Radius Access-Accept Dictionary File Radius Attributes in Access-Accept PacketsAppendix Appendix TUT Systems, Inc 100 Internet Telephone Appendix B Technical Assistance and Customer SupportTechnical Support Equipment Return and RepairLimitations of Warranty Appendix C SMS2000 Limited WarrantyHardware Limited Warranty Exclusive RemediesAssistance Electrical Safety AdvisoryTut Systems, Inc., Customer Service Department FCC Radio Frequency Interference StatementTUT Systems, Inc 104