Tyan Computer S2912 warranty

Page 29

The following pictures illustrate how to connect an SATA drive

1.SATA drive cable connection

2. SATA drive power connection

3. SATA cable motherboard connector

4. SATA drive power adapter

Attaching Floppy Drive Cables

Attaching floppy diskette drives are done in a similar manner to hard drives. See the picture below for an example of a floppy cable. Most of the current floppy drives on the market require that the cable be installed with the colored stripe positioned next to the power connector. In most cases, there will be a key pin on the cable which will force a proper connection of the cable.

Attach first floppy drive (drive A:) to the end of the cable with the twist in it. Drive B: is usually connected to the next possible connector on the cable (the second or third connector after you install Drive A:).

http://www.tyan.com

Image 29

Contents S2912 Thunder n3600RBoard Installation Table of Contents IntroductionBios DiagnosticsCheck the box contents Page Congratulations Hardware SpecificationsIntroduction Expansion Slots System ManagementForm Factor RegulatoryBoard Installation Board Image Thunder n3600R S2912WG2NR Block Diagram Block DiagramThunder n3600R S2912G2NR Block Diagram Jumper Legend Board Parts, Jumpers and ConnectorsFRNTUSB23 J3 FRNTUSB45 J4 Jumper/Connector FunctionPage SYSFAN7 4-pin CPU Fan Connector SYSFAN5/6 3-pin Fan ConnectorFRNTUSB45 J26 Tyfp Front Panel Header Ipmb J14 Ipmb ConnectorJ2/J3/J4 USB Front Panel Header J2/J4 COM2 J15 Tyan Front Panel 2 for Barebone reserved COM2 J95 COM2 HeaderJ113 LCD Model Pin Header JP2 JP3 JP1 JP1 SAS Disable Jumper for S2912WG2NR only J111 Fan Connector for Barebone reservedJP3 Clear Cmos Jumper Normal Default JP2 Opma Card Supporting Select JumperTips on Installing Motherboard in Chassis Installing the Processors Back plate Assembly Page Installing the Memory Memory Installation Procedure Refer to the following table for supported DDR2 populations Attaching IDE Drive Cable Attaching Drive CablesPage Installing Add-In Cards LAN LED Color Definition Connecting External DevicesApplying power to the board Installing the Power SupplyFinishing Up Starting Setup BiosAbout the Bios Getting Help Case of ProblemsSetup Variations Main Bios Setup Main System Time / System Date Extended MemoryCache Ram Reset Configuration Data Installed O/SAdvanced LPC PortHT-LDT Frequency Hammer ConfigurationNode Interleave Dram Bank InterleaveECC Options Sub-Menu ECC Mode Multiprocessor SpecificationECC Error Checking Auto DQS TrainingL2 ECC Scrub Control ECC Error LogDram ECC Scrub Control ECC Scrub RedirectionIommu Size IommuIntegrated Devices USB Bios Legacy SupportUSB Control Self-HealingMAC2 LAN Bridge Interrupt ModeMAC Address Azalia CodecNV RAID Configuration Sub-Menu FirstWare Language FirstWare ConfigurationIntegrated SAS Controller Sub-Menu PCI Configuration Available Oprom SpacePage Local Bus IDE Adapter IDE ConfigurationLarge Disk Access Mode Primary Master/Slave Sub-Menu LBA Mode ControlType Multi-Sector TransfersBit I/O Transfer ModeUltra DMA Mode Legacy Diskette a Selects floppy type Floppy ConfigurationSerial Port a 7 I/O Device ConfigurationBase I/O Address InterruptMode Parallel PortDMA Channel Floppy Disk ControllerCOM Port Address Console RedirectionBaud Rate Console TypeEvent Log Capacity DMI Event LoggingEvent Log Validity View DMI Event LogHardware Monitoring AutoFan ModeSecurity Excluded from boot order BootBoot Priority Order Enable Acpi PowerPower Button Off Tgio Spread SpectrumHigh Precision Event timer After Power FailureAMD PowerNow Sata Spread SpectrumExit Page Memory, Video, CPU DiagnosticsFlash Utility Code Beeps / Description Phoenix Bios Post CodeDisplay shadow-area Code Beeps / Description Appendix I How to Make a Driver Diskette NVidia ====Choose Chipset Model==== NVidia Nvraid Glossary Page Page Page Page Page Technical Support Returning Merchandise for Service