Tyan Computer S2912 warranty Advanced, Installed O/S, Reset Configuration Data, LPC Port

Page 39

3.4 Advanced

This section facilitates configuring advanced BIOS options for your system.

Installed O/S

This allows you to select the operating system installed on your system which you will use most commonly.

NOTE: An incorrect setting can cause the operating system to behave unpredictably.

Options: Other / Win95 / Win98 / WinMe / WinXP64

Reset Configuration Data

If you install a new piece of hardware or modify your computer's hardware configuration, the BIOS will automatically detect the changes and reconfigure the ESCD (Extended System Configuration Data). Therefore, there is usually no need to manually force the BIOS to reconfigure the ESCD.

Select [Yes] if you want to clear the ESCD area. Options: Yes / No

LPC Port 80

This item allows you to enable or disable the LPC Port 80. Disable to use the PCI port 80 card.

Options: Enabled / Disabled

39

http://www.tyan.com

Image 39

Contents S2912 Thunder n3600RDiagnostics Table of Contents IntroductionBoard Installation BiosCheck the box contents Page Hardware Specifications IntroductionCongratulations Regulatory System ManagementExpansion Slots Form FactorBoard Installation Board Image Thunder n3600R S2912WG2NR Block Diagram Block DiagramThunder n3600R S2912G2NR Block Diagram Jumper Legend Board Parts, Jumpers and ConnectorsFRNTUSB23 J3 FRNTUSB45 J4 Jumper/Connector FunctionPage SYSFAN7 4-pin CPU Fan Connector SYSFAN5/6 3-pin Fan ConnectorFRNTUSB45 Ipmb J14 Ipmb Connector J2/J3/J4 USB Front Panel Header J2/J4J26 Tyfp Front Panel Header COM2 COM2 J95 COM2 Header J113 LCD Model Pin HeaderJ15 Tyan Front Panel 2 for Barebone reserved JP2 JP3 JP1 JP2 Opma Card Supporting Select Jumper J111 Fan Connector for Barebone reservedJP1 SAS Disable Jumper for S2912WG2NR only JP3 Clear Cmos Jumper Normal DefaultTips on Installing Motherboard in Chassis Installing the Processors Back plate Assembly Page Installing the Memory Memory Installation Procedure Refer to the following table for supported DDR2 populations Attaching IDE Drive Cable Attaching Drive CablesPage Installing Add-In Cards LAN LED Color Definition Connecting External DevicesApplying power to the board Installing the Power SupplyFinishing Up Bios About the BiosStarting Setup Case of Problems Setup VariationsGetting Help Main Bios Setup Main Extended Memory Cache RamSystem Time / System Date LPC Port Installed O/SReset Configuration Data AdvancedDram Bank Interleave Hammer ConfigurationHT-LDT Frequency Node InterleaveAuto DQS Training Multiprocessor SpecificationECC Options Sub-Menu ECC Mode ECC Error CheckingECC Scrub Redirection ECC Error LogL2 ECC Scrub Control Dram ECC Scrub ControlIommu Size IommuSelf-Healing USB Bios Legacy SupportIntegrated Devices USB ControlAzalia Codec Interrupt ModeMAC2 LAN Bridge MAC AddressNV RAID Configuration Sub-Menu FirstWare Language FirstWare ConfigurationIntegrated SAS Controller Sub-Menu PCI Configuration Available Oprom SpacePage IDE Configuration Large Disk Access ModeLocal Bus IDE Adapter Multi-Sector Transfers LBA Mode ControlPrimary Master/Slave Sub-Menu TypeTransfer Mode Ultra DMA ModeBit I/O Legacy Diskette a Selects floppy type Floppy ConfigurationInterrupt 7 I/O Device ConfigurationSerial Port a Base I/O AddressFloppy Disk Controller Parallel PortMode DMA ChannelConsole Type Console RedirectionCOM Port Address Baud RateView DMI Event Log DMI Event LoggingEvent Log Capacity Event Log ValidityHardware Monitoring AutoFan ModeSecurity Boot Boot Priority OrderExcluded from boot order Tgio Spread Spectrum PowerEnable Acpi Power Button OffSata Spread Spectrum After Power FailureHigh Precision Event timer AMD PowerNowExit Page Diagnostics Flash UtilityMemory, Video, CPU Code Beeps / Description Phoenix Bios Post CodeDisplay shadow-area Code Beeps / Description Appendix I How to Make a Driver Diskette NVidia ====Choose Chipset Model==== NVidia Nvraid Glossary Page Page Page Page Page Technical Support Returning Merchandise for Service