Tyan Computer S2912 Console Redirection, COM Port Address, Baud Rate, Console Type, Flow Control

Page 56

3.4.8 Console Redirection

This setting allows you to configure Console Redirection.

COM Port Address

If enabled, it will use a port on the motherboard.

Options: Enabled / Disabled

Baud Rate

Enables the specified baud rate.

Options: 300 / 1200 / 2400 / 9600 / 19.2K / 38.4K / 57.6K / 115.2K

Console Type

Enables the specified console type.

Options: VT100 / VT100, 8bit / PC-ANSI / VT100+ / VT-UTF8 / ASCII

Flow Control

Enables flow control.

Options: Disabled / XON/XOFF / CTS/RTS

Console Connection

It indicates whether the console is connected directly to the system or a modem is used to connect.

Options: Direct / via Modem

Continue C.R. After POST

Enables Console Redirection after OS has loaded.

Options: Off / On

56

http://www.tyan.com

Image 56

Contents Thunder n3600R S2912Table of Contents Introduction Board InstallationBios DiagnosticsCheck the box contents Page Congratulations Hardware SpecificationsIntroduction System Management Expansion SlotsForm Factor RegulatoryBoard Installation Board Image Block Diagram Thunder n3600R S2912WG2NR Block DiagramThunder n3600R S2912G2NR Block Diagram Board Parts, Jumpers and Connectors Jumper LegendJumper/Connector Function FRNTUSB23 J3 FRNTUSB45 J4Page SYSFAN5/6 3-pin Fan Connector SYSFAN7 4-pin CPU Fan ConnectorFRNTUSB45 J26 Tyfp Front Panel Header Ipmb J14 Ipmb ConnectorJ2/J3/J4 USB Front Panel Header J2/J4 COM2 J15 Tyan Front Panel 2 for Barebone reserved COM2 J95 COM2 HeaderJ113 LCD Model Pin Header JP2 JP3 JP1 J111 Fan Connector for Barebone reserved JP1 SAS Disable Jumper for S2912WG2NR onlyJP3 Clear Cmos Jumper Normal Default JP2 Opma Card Supporting Select JumperTips on Installing Motherboard in Chassis Installing the Processors Back plate Assembly Page Installing the Memory Memory Installation Procedure Refer to the following table for supported DDR2 populations Attaching Drive Cables Attaching IDE Drive CablePage Installing Add-In Cards Connecting External Devices LAN LED Color DefinitionInstalling the Power Supply Applying power to the boardFinishing Up Starting Setup BiosAbout the Bios Getting Help Case of ProblemsSetup Variations Main Bios Setup Main System Time / System Date Extended MemoryCache Ram Installed O/S Reset Configuration DataAdvanced LPC PortHammer Configuration HT-LDT FrequencyNode Interleave Dram Bank InterleaveMultiprocessor Specification ECC Options Sub-Menu ECC ModeECC Error Checking Auto DQS TrainingECC Error Log L2 ECC Scrub ControlDram ECC Scrub Control ECC Scrub RedirectionIommu Iommu SizeUSB Bios Legacy Support Integrated DevicesUSB Control Self-HealingInterrupt Mode MAC2 LAN BridgeMAC Address Azalia CodecNV RAID Configuration Sub-Menu FirstWare Configuration FirstWare LanguagePCI Configuration Available Oprom Space Integrated SAS Controller Sub-MenuPage Local Bus IDE Adapter IDE ConfigurationLarge Disk Access Mode LBA Mode Control Primary Master/Slave Sub-MenuType Multi-Sector TransfersBit I/O Transfer ModeUltra DMA Mode Floppy Configuration Legacy Diskette a Selects floppy type7 I/O Device Configuration Serial Port aBase I/O Address InterruptParallel Port ModeDMA Channel Floppy Disk ControllerConsole Redirection COM Port AddressBaud Rate Console TypeDMI Event Logging Event Log CapacityEvent Log Validity View DMI Event LogAutoFan Mode Hardware MonitoringSecurity Excluded from boot order BootBoot Priority Order Power Enable AcpiPower Button Off Tgio Spread SpectrumAfter Power Failure High Precision Event timerAMD PowerNow Sata Spread SpectrumExit Page Memory, Video, CPU DiagnosticsFlash Utility Phoenix Bios Post Code Code Beeps / DescriptionDisplay shadow-area Code Beeps / Description Appendix I How to Make a Driver Diskette NVidia ====Choose Chipset Model==== NVidia Nvraid Glossary Page Page Page Page Page Returning Merchandise for Service Technical Support