Tyan Computer S2912 warranty Connecting External Devices, LAN LED Color Definition

Page 31

2.9 - Connecting External Devices

Your motherboard supports a number of different interfaces for connecting peripherals. Some I/O ports may not be available with the board due to the different configurations.

PS/2 Mouse/Keyboard

Serial Port		VGA Port		LAN2		LAN1

RJ-45 for OPMA

USB x 2

Peripheral devices can be plugged straight into any of these ports but software may be required to complete the installation.

LAN LED Color Definition

The onboard Ethernet port has green and yellow LEDs to indicate LAN status. The chart below illustrates the different LED states.

		Description耟	Left LED	Right LED
		No Link	OFF	OFF
Le ft	Righ t	Link 10Mbps	GREEN	OFF
		Activity 10Mbps	GREEN(blink)	Green
		Linked at 100Mbps	Green	Green
		Activity 100Mbps	Green(blink)	Green(blink)
	耟	Linked at 1000Mbps	OFF	Green
		Activity 1000Mbps	OFF	Green(blink)

31

http://www.tyan.com

Image 31

Contents S2912 Thunder n3600RDiagnostics Table of Contents IntroductionBoard Installation BiosCheck the box contents Page Introduction Hardware SpecificationsCongratulations Regulatory System ManagementExpansion Slots Form FactorBoard Installation Board Image Thunder n3600R S2912WG2NR Block Diagram Block DiagramThunder n3600R S2912G2NR Block Diagram Jumper Legend Board Parts, Jumpers and ConnectorsFRNTUSB23 J3 FRNTUSB45 J4 Jumper/Connector FunctionPage SYSFAN7 4-pin CPU Fan Connector SYSFAN5/6 3-pin Fan ConnectorFRNTUSB45 J2/J3/J4 USB Front Panel Header J2/J4 Ipmb J14 Ipmb ConnectorJ26 Tyfp Front Panel Header COM2 J113 LCD Model Pin Header COM2 J95 COM2 HeaderJ15 Tyan Front Panel 2 for Barebone reserved JP2 JP3 JP1 JP2 Opma Card Supporting Select Jumper J111 Fan Connector for Barebone reservedJP1 SAS Disable Jumper for S2912WG2NR only JP3 Clear Cmos Jumper Normal DefaultTips on Installing Motherboard in Chassis Installing the Processors Back plate Assembly Page Installing the Memory Memory Installation Procedure Refer to the following table for supported DDR2 populations Attaching IDE Drive Cable Attaching Drive CablesPage Installing Add-In Cards LAN LED Color Definition Connecting External DevicesApplying power to the board Installing the Power SupplyFinishing Up About the Bios BiosStarting Setup Setup Variations Case of ProblemsGetting Help Main Bios Setup Main Cache Ram Extended MemorySystem Time / System Date LPC Port Installed O/SReset Configuration Data AdvancedDram Bank Interleave Hammer ConfigurationHT-LDT Frequency Node InterleaveAuto DQS Training Multiprocessor SpecificationECC Options Sub-Menu ECC Mode ECC Error CheckingECC Scrub Redirection ECC Error LogL2 ECC Scrub Control Dram ECC Scrub ControlIommu Size IommuSelf-Healing USB Bios Legacy SupportIntegrated Devices USB ControlAzalia Codec Interrupt ModeMAC2 LAN Bridge MAC AddressNV RAID Configuration Sub-Menu FirstWare Language FirstWare ConfigurationIntegrated SAS Controller Sub-Menu PCI Configuration Available Oprom SpacePage Large Disk Access Mode IDE ConfigurationLocal Bus IDE Adapter Multi-Sector Transfers LBA Mode ControlPrimary Master/Slave Sub-Menu TypeUltra DMA Mode Transfer ModeBit I/O Legacy Diskette a Selects floppy type Floppy ConfigurationInterrupt 7 I/O Device ConfigurationSerial Port a Base I/O AddressFloppy Disk Controller Parallel PortMode DMA ChannelConsole Type Console RedirectionCOM Port Address Baud RateView DMI Event Log DMI Event LoggingEvent Log Capacity Event Log ValidityHardware Monitoring AutoFan ModeSecurity Boot Priority Order BootExcluded from boot order Tgio Spread Spectrum PowerEnable Acpi Power Button OffSata Spread Spectrum After Power FailureHigh Precision Event timer AMD PowerNowExit Page Flash Utility DiagnosticsMemory, Video, CPU Code Beeps / Description Phoenix Bios Post CodeDisplay shadow-area Code Beeps / Description Appendix I How to Make a Driver Diskette NVidia ====Choose Chipset Model==== NVidia Nvraid Glossary Page Page Page Page Page Technical Support Returning Merchandise for Service