Tyan Computer S2912 Hammer Configuration, HT-LDT Frequency, Node Interleave, Dram Bank Interleave

Page 40

3.4.1 Hammer Configuration

This section allows you to fine tune the hammer configuration.

HT-LDT Frequency

The port’s transmission frequency.

Options: 1000MHz / 800MHz / 600MHz / 400MHz / 200MHz

Node Interleave

Interleave memory blocks across nodes. Auto will set this enabled when possible. Options: Disabled / Auto

DRAM Bank Interleave

Interleave memory blocks across the DRM chip selects. Auto will set this enabled when possible.

Options: Disabled / Auto

Set FID to MaxFID

Enable this option to set the FID to MaxFID on fused, non-server parts. It also sets the VID to 50mV less than the MaxFID. Disable this option to leave the FID alone. For unfused parts or server parts, enabled will do nothing.

Options: Auto / Disabled

Online Spare

Enable the DRAM controller to designate a DIMM bank as a spare for logical swap during runtime.

Options: Disabled / Enabled

40

http://www.tyan.com

Image 40

Contents Thunder n3600R S2912Table of Contents Introduction Board InstallationBios DiagnosticsCheck the box contents Page Introduction Hardware SpecificationsCongratulations System Management Expansion SlotsForm Factor RegulatoryBoard Installation Board Image Block Diagram Thunder n3600R S2912WG2NR Block DiagramThunder n3600R S2912G2NR Block Diagram Board Parts, Jumpers and Connectors Jumper LegendJumper/Connector Function FRNTUSB23 J3 FRNTUSB45 J4Page SYSFAN5/6 3-pin Fan Connector SYSFAN7 4-pin CPU Fan ConnectorFRNTUSB45 J2/J3/J4 USB Front Panel Header J2/J4 Ipmb J14 Ipmb ConnectorJ26 Tyfp Front Panel Header COM2 J113 LCD Model Pin Header COM2 J95 COM2 HeaderJ15 Tyan Front Panel 2 for Barebone reserved JP2 JP3 JP1 J111 Fan Connector for Barebone reserved JP1 SAS Disable Jumper for S2912WG2NR onlyJP3 Clear Cmos Jumper Normal Default JP2 Opma Card Supporting Select JumperTips on Installing Motherboard in Chassis Installing the Processors Back plate Assembly Page Installing the Memory Memory Installation Procedure Refer to the following table for supported DDR2 populations Attaching Drive Cables Attaching IDE Drive CablePage Installing Add-In Cards Connecting External Devices LAN LED Color DefinitionInstalling the Power Supply Applying power to the boardFinishing Up About the Bios BiosStarting Setup Setup Variations Case of ProblemsGetting Help Main Bios Setup Main Cache Ram Extended MemorySystem Time / System Date Installed O/S Reset Configuration DataAdvanced LPC PortHammer Configuration HT-LDT FrequencyNode Interleave Dram Bank InterleaveMultiprocessor Specification ECC Options Sub-Menu ECC ModeECC Error Checking Auto DQS TrainingECC Error Log L2 ECC Scrub ControlDram ECC Scrub Control ECC Scrub RedirectionIommu Iommu SizeUSB Bios Legacy Support Integrated DevicesUSB Control Self-HealingInterrupt Mode MAC2 LAN BridgeMAC Address Azalia CodecNV RAID Configuration Sub-Menu FirstWare Configuration FirstWare LanguagePCI Configuration Available Oprom Space Integrated SAS Controller Sub-MenuPage Large Disk Access Mode IDE ConfigurationLocal Bus IDE Adapter LBA Mode Control Primary Master/Slave Sub-MenuType Multi-Sector TransfersUltra DMA Mode Transfer ModeBit I/O Floppy Configuration Legacy Diskette a Selects floppy type7 I/O Device Configuration Serial Port aBase I/O Address InterruptParallel Port ModeDMA Channel Floppy Disk ControllerConsole Redirection COM Port AddressBaud Rate Console TypeDMI Event Logging Event Log CapacityEvent Log Validity View DMI Event LogAutoFan Mode Hardware MonitoringSecurity Boot Priority Order BootExcluded from boot order Power Enable AcpiPower Button Off Tgio Spread SpectrumAfter Power Failure High Precision Event timerAMD PowerNow Sata Spread SpectrumExit Page Flash Utility DiagnosticsMemory, Video, CPU Phoenix Bios Post Code Code Beeps / DescriptionDisplay shadow-area Code Beeps / Description Appendix I How to Make a Driver Diskette NVidia ====Choose Chipset Model==== NVidia Nvraid Glossary Page Page Page Page Page Returning Merchandise for Service Technical Support