Tyan Computer S2460 user manual 266MHz 200MHz, D. Front-side USB Header* J36, USB Header J36

Page 13

2.6-C. CPU Front Side Bus Jumpers (J48, J49; J52, J53) (READ NOTE BELOW)

With these jumpers, the CPU FSB can be set to either 200 or 266MHz.

NOTE:

YOU MUST SET THESE JUMPERS FOR PROPER CPU OPERATION. If your CPU can only run at 200MHz, altering these FSB jumpers will not make the CPU run at 266MHz.

Tyan takes no reponsibility and will not be held liable for damage related to opera- tion of the CPU using different settings from those of the CPU manufacturer’s specified default settings.

NOTE:

You MUST set ALL FOUR JUMPERS to the same speed. Damage may result otherwise!

 

 

 

 

 

 

266MHz

200MHz

 

 

 

 

 

 

 

 

 

 

 

 

 

J52

2-3

1-2

 

 

 

 

 

J53

2-3

2-3

 

 

 

 

 

 

 

 

J48

J49

1-2

2-3

 

 

1-2

2-3

 

 

2.6-D. Front-side USB Header* (J36)

This header allows for a USB connection*. The USB channel on this header is on a separate channel from the rear USB connections channel. USB v1.1 is supported on this board.

USB Header (J36)

+VCC

1

2

ground

signal out

3

4

ground

signal in

5

6

signal in

ground

7

8

signal out

ground

9

10

+VCC

*Only certain chassis allow for frontside USB connection. Please check with your chassis vendor for details on frontside USB connections. Tyan does not provide frontside USB cables.

Tiger MP S2460

13

Image 13
Contents User’s Manual Tiger MPTable of Contents System Resources Before you begin Check the box contentsCongratulations IntroductionDDR Sdram Tiger MP System Block DiagramBios Hardware SpecificationsForm Factor Regulatory Software SpecificationsInstallation Board InstallationHow to install our products right.. the first time Here are some safety tipsQuick References for Jumpers AMD-760 Map of Motherboard JumpersSLP PWR RST Setting up Jumpers and Onboard ConnectorsLED KEY PWR Speaker LEDD. Front-side USB Header* J36 266MHz 200MHzUSB Header J36 E. FAN Headers P0FAN, P1FAN, FAN1, FAN2, FAN3 SpecificationsFAN Ground +12V SpeedH. Reserved Jumper* J34 Reserved G. SMBus Connector* J89J. Hardware Reset Switch Connector Installation I. Soft Power ConnectorPWR LED PWR RSTK. Flash Utility BiosMounting the Motherboard into the Chassis Memory Installation Procedure Installing MemoryRemoving a Dimm Dimm Suggested Memory ConfigurationsTotal 128MB 192MB 256MB 512MB 1024MB 2048MB 3072MB 3584MBInstalling the CPU Installing the CPU and Cooling FanInstalling Chassis Fans Installing the Cooling FansConnector is WHITE. See the picture to the rightfor an Connecting IDE and Floppy DrivesSome symptoms of incorrectly installed HDDs are HDDs are not auto-detectedSome symptoms of incorrectly installed FDDs are Connecting Floppy DrivesFloppy Drive Fail message at bootup FDD does not power on FDD light is constantly onInstalling Add-on Cards Connecting Serial and Parallel Ports Connecting PS/2, USB, and Serial DevicesThis is normal Connecting the power supplyThis is the Clip You are done Frequently Asked Questions FAQ Introduction to the Bios setup Bios SetupKey Function Legacy Diskette a ..B Main SetupCylinders TypeHeads Sectors/TrackTransfer Mode LBA Mode ControlMulti-Sector Transfers Bit I/OUSB Bios Legacy Support Reset Configuration DataChipset Configuration Keyboard ConfigurationBase I/O ModeInterrupt Serr Signal Condition PCI ConfigurationECC Config DMA ChannelNumLock Keyboard auto-repeat delayKeyboard auto-repeat rate PS/2 MouseDC00 Dfff CC00 CfffPassword on boot Set Supervisor PasswordFixed disk boot sector Diskette AccessAuto Suspend Timeout Standby TimeoutResume on modem ring Resume on timeDetected Load Setup DefaultsExit Saving Changes Exit Discarding ChangesFlash Utility Beep CodesAppendix I Glossary Page Tiger MP S2460 Mirroring see RAID IPL see Initial Program LoadTiger MP S2460 Striping see RAID Technical Support Returning Merchandise for ServiceHelp Resources Check the Tyan user group alt.comp.periphs.mainboard.tyanDocument # D1461-103