Tyan Computer S2460 E. FAN Headers P0FAN, P1FAN, FAN1, FAN2, FAN3, Fan, Ground +12V Speed

Page 14

2.6-E. FAN Headers (P0FAN, P1FAN, FAN1, FAN2, FAN3)

These headers allow for extra fans to be installed. P0FAN and P1FAN are reserved for CPU0 and CPU1 (respectively). All other fans are left to the user’s discretion.

P0FAN

FAN3

P1FAN

FAN1

FAN2

FAN

1

2

3

ground

+12V

speed

Specifications

Voltage

12V

Amperage

300mA

NOTE:

The FAN connector has a 12V, 300mA limitation. Tyan takes no responsibility and will not be held liable for damage related to the misuse of any FAN header.

2.6-F. Chassis Intrusion* Header (J90) (RESERVED)

This header is provided in the event that your chassis has a chassis intrusion feature*, and that an appli- cation is available to manage this feature.

J90

* Indicates an optional feature, may not be available on some Tiger MP models

14

http://www.tyan.com

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Tiger MP User’s ManualTable of Contents System Resources Check the box contents Before you beginIntroduction CongratulationsTiger MP System Block Diagram DDR SdramHardware Specifications BiosSoftware Specifications Form Factor RegulatoryHow to install our products right.. the first time Board InstallationInstallation Here are some safety tipsQuick References for Jumpers Map of Motherboard Jumpers AMD-760LED Setting up Jumpers and Onboard ConnectorsSLP PWR RST KEY PWR Speaker LEDUSB Header J36 266MHz 200MHzD. Front-side USB Header* J36 FAN SpecificationsE. FAN Headers P0FAN, P1FAN, FAN1, FAN2, FAN3 Ground +12V SpeedG. SMBus Connector* J89 H. Reserved Jumper* J34 ReservedPWR LED I. Soft Power ConnectorJ. Hardware Reset Switch Connector Installation PWR RSTBios K. Flash UtilityMounting the Motherboard into the Chassis Installing Memory Memory Installation ProcedureRemoving a Dimm Total Suggested Memory ConfigurationsDimm 128MB 192MB 256MB 512MB 1024MB 2048MB 3072MB 3584MBInstalling the CPU and Cooling Fan Installing the CPUInstalling the Cooling Fans Installing Chassis FansSome symptoms of incorrectly installed HDDs are Connecting IDE and Floppy DrivesConnector is WHITE. See the picture to the rightfor an HDDs are not auto-detectedFloppy Drive Fail message at bootup Connecting Floppy DrivesSome symptoms of incorrectly installed FDDs are FDD does not power on FDD light is constantly onInstalling Add-on Cards Connecting PS/2, USB, and Serial Devices Connecting Serial and Parallel PortsThis is the Clip Connecting the power supplyThis is normal You are done Frequently Asked Questions FAQ Bios Setup Introduction to the Bios setupKey Function Main Setup Legacy Diskette a ..BHeads TypeCylinders Sectors/TrackMulti-Sector Transfers LBA Mode ControlTransfer Mode Bit I/OChipset Configuration Reset Configuration DataUSB Bios Legacy Support Keyboard ConfigurationInterrupt ModeBase I/O ECC Config PCI ConfigurationSerr Signal Condition DMA ChannelKeyboard auto-repeat rate Keyboard auto-repeat delayNumLock PS/2 MouseCC00 Cfff DC00 DfffFixed disk boot sector Set Supervisor PasswordPassword on boot Diskette AccessResume on modem ring Standby TimeoutAuto Suspend Timeout Resume on timeExit Saving Changes Load Setup DefaultsDetected Exit Discarding ChangesBeep Codes Flash UtilityAppendix I Glossary Page Tiger MP S2460 IPL see Initial Program Load Mirroring see RAIDTiger MP S2460 Striping see RAID Help Resources Returning Merchandise for ServiceTechnical Support Check the Tyan user group alt.comp.periphs.mainboard.tyanDocument # D1461-103
Top Page Image Contents