Tyan Computer S2460 Detected, Exit Saving Changes, Exit Discarding Changes, Load Setup Defaults

Page 43

3.5 Boot Setup

Boot settings can be altered through this screen. All options are arranged by vertical priority.

 

 

FORMAT:

[option]

 

 

 

OPTIONS:

(dependent on

Each item detected as a

 

 

 

devices detected)

removeable device, will

 

 

 

 

be listed in this section.

(menu dependent on devices

 

 

 

As the user presses the

detected

 

 

 

 

 

 

‘+’ key, the item will move

 

 

 

 

up in priority. The item at

 

 

 

 

the top will take first prior-

 

 

 

 

ity, the second item takes

 

 

 

 

next highest priority, and

 

 

 

 

so on.

3.6 Exit Menu

 

 

 

Selecting “Exit” will display this menu.

 

 

 

 

 

 

 

 

 

 

FORMAT:

[option]

 

Exit Saving Changes

 

OPTIONS:

Yes

Saves changes to CMOS

 

 

 

No

and exits BIOS setup.

 

 

 

 

 

 

 

FORMAT:

[option]

 

Exit Discarding Changes

 

OPTIONS:

Yes

Discard any changes and

 

 

 

No

then exit BIOS setup.

 

 

 

 

 

 

 

FORMAT:

[option]

 

Load Setup Defaults

 

OPTIONS:

Yes

Loads preset defaults

 

 

 

No

from CMOS.

 

 

 

 

 

 

 

FORMAT:

[option]

 

Discard Changes

 

OPTIONS:

Yes

Discards all changes.

 

 

 

No

 

 

 

 

 

 

 

 

FORMAT:

[option]

 

Save Changes

 

OPTIONS:

Yes

Saves all changes.

 

 

 

No

 

Tiger MP S2460

43

Image 43
Contents User’s Manual Tiger MPTable of Contents System Resources Before you begin Check the box contentsCongratulations IntroductionDDR Sdram Tiger MP System Block DiagramBios Hardware SpecificationsForm Factor Regulatory Software SpecificationsHere are some safety tips Board InstallationInstallation How to install our products right.. the first timeQuick References for Jumpers AMD-760 Map of Motherboard JumpersKEY PWR Speaker LED Setting up Jumpers and Onboard ConnectorsSLP PWR RST LEDD. Front-side USB Header* J36 266MHz 200MHzUSB Header J36 Ground +12V Speed SpecificationsE. FAN Headers P0FAN, P1FAN, FAN1, FAN2, FAN3 FANH. Reserved Jumper* J34 Reserved G. SMBus Connector* J89PWR RST I. Soft Power ConnectorJ. Hardware Reset Switch Connector Installation PWR LEDK. Flash Utility BiosMounting the Motherboard into the Chassis Memory Installation Procedure Installing MemoryRemoving a Dimm 128MB 192MB 256MB 512MB 1024MB 2048MB 3072MB 3584MB Suggested Memory ConfigurationsDimm TotalInstalling the CPU Installing the CPU and Cooling FanInstalling Chassis Fans Installing the Cooling FansHDDs are not auto-detected Connecting IDE and Floppy DrivesConnector is WHITE. See the picture to the rightfor an Some symptoms of incorrectly installed HDDs areFDD does not power on FDD light is constantly on Connecting Floppy DrivesSome symptoms of incorrectly installed FDDs are Floppy Drive Fail message at bootupInstalling Add-on Cards Connecting Serial and Parallel Ports Connecting PS/2, USB, and Serial DevicesThis is normal Connecting the power supplyThis is the Clip You are done Frequently Asked Questions FAQ Introduction to the Bios setup Bios SetupKey Function Legacy Diskette a ..B Main SetupSectors/Track TypeCylinders HeadsBit I/O LBA Mode ControlTransfer Mode Multi-Sector TransfersKeyboard Configuration Reset Configuration DataUSB Bios Legacy Support Chipset ConfigurationBase I/O ModeInterrupt DMA Channel PCI ConfigurationSerr Signal Condition ECC ConfigPS/2 Mouse Keyboard auto-repeat delayNumLock Keyboard auto-repeat rateDC00 Dfff CC00 CfffDiskette Access Set Supervisor PasswordPassword on boot Fixed disk boot sectorResume on time Standby TimeoutAuto Suspend Timeout Resume on modem ringExit Discarding Changes Load Setup DefaultsDetected Exit Saving ChangesFlash Utility Beep CodesAppendix I Glossary Page Tiger MP S2460 Mirroring see RAID IPL see Initial Program LoadTiger MP S2460 Striping see RAID Check the Tyan user group alt.comp.periphs.mainboard.tyan Returning Merchandise for ServiceTechnical Support Help ResourcesDocument # D1461-103