Omega Vehicle Security PTC900 Installing PLUG-IN Cards, Wiring the Meter, TOP View, To Install

Page 7

3.0INSTALLING PLUG-IN CARDS

The Plug-in cards are separately purchased optional cards that perform specific functions. These cards plug into the main circuit board of the meter. The Plug-in cards have many unique functions when used with the meters.

CAUTION: The Plug-in card and main circuit board contain static sensitive components. Before handling the cards, discharge static charges from your body by touching a grounded bare metal object. Ideally, handle the cards at a static controlled clean workstation. Also, only handle the cards by the edges. Dirt, oil or other contaminants that may contact the cards can adversely affect circuit operation.

TOP VIEW

To Install:

1.With the case open, locate the Plug-in card connector for the card type to be installed. The types are keyed by position with different main circuit board connector locations. When installing the card, hold the meter by the rear terminals and not by the front display board.*

2.Install the Plug-in card by aligning the card terminals with the slot bay in the rear cover. Be sure the connector is fully engaged and the tab on the Plug-in card rests in the alignment slot on the display board.

3.Slide the meter base back into the case. Be sure the rear cover latches fully into the case.

4.Apply the Plug-in card label to the bottom side of the meter. Do Not Cover the vents on the top surface of the meter. The surface of the case must be clean for the label to adhere properly. Apply the label to the area designated by the large case label.

Quad Sourcing Open Collector Output Card Supply Select

*If installing the Quad sourcing Plug-in Card (LDP6-CDS40), set the jumper for internal or external supply operation before continuing.

4.0WIRING THE METER

WIRING OVERVIEW

Electrical connections are made via screw-clamp terminals located on the back of the meter. All conductors should conform to the meter’s voltage and current ratings. All cabling should conform to appropriate standards of good installation, local codes and regulations. It is recommended that the power supplied to the meter (DC or AC) be protected by a fuse or circuit breaker.

When wiring the meter, compare the numbers embossed on the back of the meter case against those shown in wiring drawings for proper wire position. Strip the wire, leaving approximately 0.3" (7.5 mm) bare lead exposed (stranded wires should be tinned with solder.) Insert the lead under the correct screw- clamp terminal and tighten until the wire is secure. (Pull wire to verify tightness.) Each terminal can accept up to one #14 AWG (2.55 mm) wire, two #18 AWG (1.02 mm), or four #20 AWG (0.61 mm).

EMC INSTALLATION GUIDELINES

Although this meter is designed with a high degree of immunity to Electro- Magnetic Interference (EMI), proper installation and wiring methods must be followed to ensure compatibility in each application. The type of the electrical noise, source or coupling method into the meter may be different for various installations. The meter becomes more immune to EMI with fewer I/O connections. Cable length, routing, and shield termination are very important and can mean the difference between a successful or troublesome installation. Listed below are some EMC guidelines for successful installation in an industrial environment.

1.The meter should be mounted in a metal enclosure, which is properly connected to protective earth.

2.Use shielded (screened) cables for all Signal and Control inputs. The shield (screen) pigtail connection should be made as short as possible. The connection point for the shield depends somewhat upon the application. Listed below are the recommended methods of connecting the shield, in order of their effectiveness.

a.Connect the shield only at the panel where the unit is mounted to earth ground (protective earth).

b. Connect the shield to earth ground at both ends of the cable, usually when the noise source frequency is above 1 MHz.

c. Connect the shield to common of the meter and leave the other end of the shield unconnected and insulated from earth ground.

3.Never run Signal or Control cables in the same conduit or raceway with AC power lines, conductors feeding motors, solenoids, SCR controls, and heaters, etc. The cables should be ran in metal conduit that is properly grounded. This is especially useful in applications where cable runs are long and portable two-way radios are used in close proximity or if the installation is near a commercial radio transmitter.

4.Signal or Control cables within an enclosure should be routed as far as possible from contactors, control relays, transformers, and other noisy components.

5.In extremely high EMI environments, the use of external EMI suppression devices, such as ferrite suppression cores, is effective. Install them on Signal and Control cables as close to the unit as possible. Loop the cable through the core several times or use multiple cores on each cable for additional protection. Install line filters on the power input cable to the unit to suppress power line interference. Install them near the power entry point of the enclosure. The following EMI suppression devices (or equivalent) are recommended:

Ferrite Suppression Cores for signal and control cables: Fair-Rite # 0443167251

TDK # ZCAT3035-1330A Steward # 28B2029-0A0

Line Filters for input power cables: Schaffner # FN610-1/07 Schaffner # FN670-1.8/07 Corcom # 1 VR3

Note: Reference manufacturer’s instructions when installing a line filter.

6.Long cable runs are more susceptible to EMI pickup than short cable runs. Therefore, keep cable runs as short as possible.

7.Switching of inductive loads produces high EMI. Use of snubbers across inductive loads suppresses EMI.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents User’s Guide Servicing North America General Description Safety SummaryGeneral Meter Specifications Table of ContentsCommunication Cards LDP6-CDC Optional PLUG-IN Cards and AccessoriesSetpoint Cards LDP6-CDS Setting the Jumpers Installing the MeterIndicates factory setting TOP View Installing PLUG-IN CardsWiring the Meter To InstallSinking Logic AC Power DC PowerSourcing Logic RS232 Communications Setpoint PLUG-IN Card TerminalsSourcing Output Logic Card Sinking Output Logic CardWith the Host Meter automatically adjusts the minutesReviewing the Front Buttons and Display Time synchronization between multipleProgramming Menu Programming the MeterParameter Menu Module 1 Timer Input ParametersParameters Module 2 User Input and Front Panel Function KEYRtC-d DspRtC-t SP-4 SP-1SP-2 SP-3Module 3 Display and Program LOCK-OUT Parameters INt-L Module 5 Timer Operating ModesModule 4 Cycle Counter Parameters DLYINtINP OP « to Module 6 S Etpoint a Larm P ArametersLAtCH OUtSetpoint POWER-UP State Timer StopTIMER/COUNTER Auto Reset Output Reset with Display ResetSPNt Module 7 Serial Communications ParametersStrStp Command String Examples Command ChartCommand String Construction Register Identification ChartSetpoint Output Register SOR ID Auto/Manual Mode Register MMR ID UAbbreviated Transmission Meter Response ExamplesSET Time SET Date Module 8 REAL-TIME Clock ParametersSET DAY +B/ 12-59pPress DSP key to return to the Display Mode Module 9 Factory Service OperationsRestore Factory Defaults Problem RemediesUSEr-2 Sp0f-2Sp0f-3 Sp0f-4OUt-n SP-1 SP-2 SP-3 SP-4ASM-n ACt-nPTC900/PTC901 Programming Quick Overview Part Number Information AccessoriesWARRANTY/DISCLAIMER Shop online at omega.com

PTC900 specifications

The Omega Vehicle Security PTC900 is a sophisticated vehicle security system designed to provide comprehensive protection against theft and unauthorized access. This cutting-edge technology integrates advanced features and a robust design to ensure peace of mind for vehicle owners.

One of the standout characteristics of the PTC900 is its state-of-the-art immobilizer technology. The system incorporates a unique electronic key code that prevents the engine from starting unless the authorized key is present. This feature significantly deters potential thieves, making it exceedingly difficult to operate the vehicle without the proper authorization.

The PTC900 is equipped with a dual-stage shock sensor that detects both minor and significant impacts. When a disturbance is detected, the system emits a loud alarm, drawing attention and potentially scaring off intruders. This sensor capability allows for a tailored response to various threats, enhancing security without unnecessary disruptions from harmless movements.

Additionally, the Omega Vehicle Security system includes a remote keyless entry feature, allowing users to lock and unlock their vehicles from a distance conveniently. This technology not only provides ease of use but also reinforces the security system by eliminating the need for traditional keys that can be copied or misused.

Another remarkable aspect of the PTC900 is its user-friendly interface. The intuitive control panel enables quick adjustments and customizations to various security settings, allowing users to tailor the system to their specific needs. With clear indicators for system status, users can easily monitor their vehicle’s security at a glance.

The reliability of the Omega Vehicle Security system is further enhanced by its weather-resistant construction, ensuring durability under various environmental conditions. The compact design allows for seamless integration into different vehicle types without compromising aesthetics or functionality.

For those seeking enhanced peace of mind, the PTC900 also offers optional GPS tracking capabilities. This feature enables vehicle owners to monitor their vehicle's location in real time, providing an additional layer of security against theft. If the vehicle is stolen, owners can quickly share location data with law enforcement, increasing the likelihood of recovery.

In conclusion, the Omega Vehicle Security PTC900 stands out as a premium solution in vehicle protection. With its advanced immobilizer technology, dual-stage shock sensor, remote keyless entry, user-friendly features, and optional GPS tracking, it provides comprehensive security, ensuring that vehicle owners can enjoy their investments without fear.
Top Page Image Contents