Omega Vehicle Security OM-550 manual Power Connection, Battery Installation

Page 23

3.0 SET-UP

This section provides the necessary information to set the OM-550 up for proper operation.

3.1 POWER CONNECTION

As previously discussed there are several options to supply power to the OM-550 and the following sections explain how to use them.

3.1.1 BATTERY INSTALLATION

Slide the battery cover open and insert the batteries as shown below. Replace the cover and turn the unit “ON: by pressing theON-OFFkey. The OM-550 will then activate and initiate printer activity. If the OM-550 does not respond, ensure that the batteries are properly positioned.

When the batteries have been removed from the OM-550 for an extended period, the unit may activate (printer activity may begin) immediately upon insertion of the batteries, without pressing the ON-OFF key.

Figure 3-1

OM-550

u18u

Image 23

Contents Table of Contents Date Time ∙ The OM-550 Datalogger may be referred to as Logger IntroductionProduct Usage Warnings Operator Safety InformationFor protection of the OM-550 itself, observe the following Unpacking OM-550 features FeaturesOM-550 Features Activity LED & Horn Keypad ∙ ON-OFF ∙ RUN ∙ OK ∙ Stop∙ PROG/EXIT Application Channel Connectors∙ Optional Connectors To remove the Viewing Window Printer WindowSerial Data Port Battery CoverThermal Paper DC JackTilt Stand Gain AdjustPower Supplies Probe SET InputsVoltage Transducer Inputs ProbesType Thermocouple InputsData Cache Programmed FeaturesStatistics Battery Check POWER-SAVE ModeLOW Battery Operation Battery Installation Power ConnectionConnecting the DC Power Cable Connecting the AC Power AdapterPaper Installation PIN Adapter Data Port Connection∙ Programming outline 1. Select Channel ProgrammingProgramming Keys Position Print FormattingVoltage Channels Temperature ChannelsMath PSEUDO-CHANNEL Not Printing LOG IntervalThis Interval Overrun can be avoided in two ways Operation AT Full Cache Recording Time Rejection Frequency Temperature UnitsTo return to Normal mode Calibration ModeTadjust R1 = 2 R2 = V-2 Voltage Input ScalingMatching Transducers to the OM-550 Matching a Voltage TransducerR1 = 2 Matching a Current Transducer= 2.0000 VDC = R1 Data Scaling mX + b calculation Matching and Scaling a Voltage Transducer VDC Example Matching and Scaling a Current TransducerU38u Unit Labels Programmed Information OperationLog Interval Time Temperature Units Enter a Tadjust value, or press OK to finish programming U44u ∙ Performing a Manual Reset Appendix a Calibration ∙ Manual ResetManual Reset programs the OM-550 as follows Setup ∙ Calibration Procedure∙ Thermocouple Adjustment Procedure ∙ Voltage Adjustment ProcedureTo return to normal operation ∙ Exiting CAL ModeAccuracy Appendix B SpecificationsVoltage Measurement Inputs Conversion PrinterPaper Life Digital Interface RS-232Connectors POWER/CURRENT RequirementsBattery Life Physical DimensionsOM-550 DOS Software Table of Contents Introduction How to Use This ManualFonts Used in this Manual Printer CPU, RAM, Hardware∙ Hard Drive Installation Software InstallationTo start the program Starting the ProgramMaster Menu Reading Data from the OM-550 To load a LOG file Load Existing LOG FilesModify Software Configuration U6u To list data List Data on MonitorTo save data as text Print Data on PrinterSave Text File To print dataTo edit a plot label Edit Plot LabelsHOT Plot Status BAR To Magnify a portion of the Data Graph Magnify ToolMagnify MAP Magnified Area Axis Labels To select a channel to graph Channel DataTo link plot lines Channels 4 & 5 After Linking Data Graph ∙ X-Cursor Data Table ∙ Data Plots∙ X-Data Cursors To activate the Help menu Help MenuTo quit List Existing LOG Files on PrinterTo list log files Appendix a KEY Functions