Omega Vehicle Security OM-550 manual Modify Software Configuration

Page 67

2.3 MODIFY SOFTWARE CONFIGURATION

Option #3 Modify Software Configuration, on the Master menu allows the user to configure the system by selecting the serial port, printer, print orientation, company name, and next file number.

The choices made using this option will be automatically saved in a file named M51.CON when this screen is exited.

To make changes:

1. Press the key and a list of configuration items will appear.

Software Configuration Screen

2.To make new entries or change existing ones, use the up and down arrow keys to highlight the item to change. The new entry first appears on the line at the top of the screen, then it is copied to the highlighted area when you press [enter] and the highlight cursor will move down to the next item.

The following definitions explain what items can be configured using this screen.

OM-550 DOS Software

u5u

Image 67

Contents Table of Contents Date Time ∙ The OM-550 Datalogger may be referred to as Logger IntroductionProduct Usage Warnings Operator Safety InformationFor protection of the OM-550 itself, observe the following Unpacking OM-550 Features FeaturesOM-550 features Activity LED & Horn Keypad ∙ ON-OFF ∙ RUN ∙ PROG/EXIT ∙ Stop∙ OK ∙ Optional Connectors Channel ConnectorsApplication To remove the Viewing Window Printer WindowSerial Data Port Battery CoverThermal Paper DC JackTilt Stand Gain AdjustPower Supplies Probe SET InputsVoltage Transducer Inputs ProbesType Thermocouple InputsData Cache Programmed FeaturesStatistics LOW Battery Operation POWER-SAVE ModeBattery Check Battery Installation Power ConnectionConnecting the DC Power Cable Connecting the AC Power AdapterPaper Installation PIN Adapter Data Port Connection∙ Programming outline 1. Select Channel ProgrammingProgramming Keys Position Print FormattingVoltage Channels Temperature ChannelsMath PSEUDO-CHANNEL This Interval Overrun can be avoided in two ways LOG IntervalNot Printing Operation AT Full Cache Recording Time Rejection Frequency Temperature UnitsTo return to Normal mode Calibration ModeTadjust R1 = 2 R2 = V-2 Voltage Input ScalingMatching Transducers to the OM-550 Matching a Voltage Transducer= 2.0000 VDC = R1 Matching a Current TransducerR1 = 2 Data Scaling mX + b calculation Matching and Scaling a Voltage Transducer VDC Example Matching and Scaling a Current TransducerU38u Unit Labels Programmed Information OperationLog Interval Time Temperature Units Enter a Tadjust value, or press OK to finish programming U44u Manual Reset programs the OM-550 as follows Appendix a Calibration ∙ Manual Reset∙ Performing a Manual Reset Setup ∙ Calibration Procedure∙ Thermocouple Adjustment Procedure ∙ Voltage Adjustment ProcedureTo return to normal operation ∙ Exiting CAL ModeVoltage Measurement Inputs Appendix B SpecificationsAccuracy Conversion PrinterPaper Life Digital Interface RS-232Connectors POWER/CURRENT RequirementsBattery Life Physical DimensionsOM-550 DOS Software Table of Contents Introduction How to Use This ManualFonts Used in this Manual Printer CPU, RAM, Hardware∙ Hard Drive Installation Software InstallationTo start the program Starting the ProgramMaster Menu Reading Data from the OM-550 To load a LOG file Load Existing LOG FilesModify Software Configuration U6u To list data List Data on MonitorTo save data as text Print Data on PrinterSave Text File To print dataTo edit a plot label Edit Plot LabelsHOT Plot Status BAR To Magnify a portion of the Data Graph Magnify ToolMagnify MAP Magnified Area Axis Labels To select a channel to graph Channel DataTo link plot lines Channels 4 & 5 After Linking Data Graph ∙ X-Data Cursors ∙ Data Plots∙ X-Cursor Data Table To activate the Help menu Help MenuTo list log files List Existing LOG Files on PrinterTo quit Appendix a KEY Functions