Omega Vehicle Security OM-550 manual Starting the Program, To start the program

Page 63

1.0 STARTING THE PROGRAM

To start the program:

1.At the DOS prompt type the DOS command, CD (change directory), drive name, colon, backslash and the program name and hit the [enter] key.

For example, if the program in installed in the default directory C:\M50 type:

∙CD C:\M50\M50C (If you have a computer with a CGA video card).

∙CD C:\M50\M50E (If you have a computer with a EGA video card).

∙CD C:\M50\M50V (If you have a computer with a VGA video card).

∙CD C:\M50\M50H (If you have a computer with a Hercules video card).

When the program begins it will display the Master Menu.

Master Menu Screen

OM-550 DOS Software

u1u

Image 63

Contents Table of Contents Date Time ∙ The OM-550 Datalogger may be referred to as Logger IntroductionProduct Usage Warnings Operator Safety InformationFor protection of the OM-550 itself, observe the following Unpacking Features OM-550 FeaturesOM-550 features Activity LED & Horn Keypad ∙ ON-OFF ∙ RUN ∙ Stop ∙ PROG/EXIT∙ OK Channel Connectors ∙ Optional ConnectorsApplication To remove the Viewing Window Printer WindowSerial Data Port Battery CoverThermal Paper DC JackTilt Stand Gain AdjustPower Supplies Probe SET InputsVoltage Transducer Inputs ProbesType Thermocouple InputsData Cache Programmed FeaturesStatistics POWER-SAVE Mode LOW Battery OperationBattery Check Battery Installation Power ConnectionConnecting the DC Power Cable Connecting the AC Power AdapterPaper Installation PIN Adapter Data Port Connection∙ Programming outline 1. Select Channel ProgrammingProgramming Keys Position Print FormattingVoltage Channels Temperature ChannelsMath PSEUDO-CHANNEL LOG Interval This Interval Overrun can be avoided in two waysNot Printing Operation AT Full Cache Recording Time Rejection Frequency Temperature UnitsTo return to Normal mode Calibration ModeTadjust R1 = 2 R2 = V-2 Voltage Input ScalingMatching Transducers to the OM-550 Matching a Voltage TransducerMatching a Current Transducer = 2.0000 VDC = R1R1 = 2 Data Scaling mX + b calculation Matching and Scaling a Voltage Transducer VDC Example Matching and Scaling a Current TransducerU38u Unit Labels Programmed Information OperationLog Interval Time Temperature Units Enter a Tadjust value, or press OK to finish programming U44u Appendix a Calibration ∙ Manual Reset Manual Reset programs the OM-550 as follows∙ Performing a Manual Reset Setup ∙ Calibration Procedure∙ Thermocouple Adjustment Procedure ∙ Voltage Adjustment ProcedureTo return to normal operation ∙ Exiting CAL ModeAppendix B Specifications Voltage Measurement InputsAccuracy Conversion PrinterPaper Life Digital Interface RS-232Connectors POWER/CURRENT RequirementsBattery Life Physical DimensionsOM-550 DOS Software Table of Contents Introduction How to Use This Manual Fonts Used in this Manual Printer CPU, RAM, Hardware∙ Hard Drive Installation Software InstallationTo start the program Starting the ProgramMaster Menu Reading Data from the OM-550 To load a LOG file Load Existing LOG FilesModify Software Configuration U6u To list data List Data on MonitorTo save data as text Print Data on PrinterSave Text File To print dataTo edit a plot label Edit Plot LabelsHOT Plot Status BAR To Magnify a portion of the Data Graph Magnify ToolMagnify MAP Magnified Area Axis Labels To select a channel to graph Channel DataTo link plot lines Channels 4 & 5 After Linking Data Graph ∙ Data Plots ∙ X-Data Cursors∙ X-Cursor Data Table To activate the Help menu Help MenuList Existing LOG Files on Printer To list log filesTo quit Appendix a KEY Functions