Minicom Advanced Systems CMG-DCM manual Summary, Network configuration

Page 78

CMG-DCM

•a code [Xx] describing the type of program and the importance of the message (e.g. all errors have E as the second letter: see the Linux man page for syslog for full details),

•the name of the program (e.g. guardian_log) which generated the message,

•the text of the message.

5.7Summary

This link displays a page summarizing the current setup of the DCM. When you first log in to the module over its Web interface, this is the page you are initially presented with. It is divided into a number of sections:

Network configuration

This section displays basic information about the DCM's network setup. It is identical to the output from the Linux ifconfig program. A typical reading might look like this:

eth0 Link encap:Ethernet HWaddr 00:D0:1F:34:EB:08

inet addr:192.168.0.46 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

RX packets:3619 errors:0 dropped:0 overruns:0 frame:0 TX packets:2453 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100

78

Issue A

Image 78

Contents CMG-DCM Table of Contents December Inside the DCM Introduction CMG-DCM Inside the DCM Serial port services Network servicesSee .4, Connecting to a local network for full details Installing the CMG-DCM Power supplyOverview Connecting to a single computer Connecting over a serial linkConnecting over Ethernet 192.168.0.xUsing an internal modem Connecting over USBConnecting to a local network Gcfgdbset option-namenew-value Wi-Fi Connecting to the InternetConnecting digitizers and external hardware Setting up the CMG-DCMWeb setup Setting up digitizers Using Scream Usage General notesDCM as a data store Gnblocks port-number Page CMG-DCM DCM as a GCF data source Accessing the DCM command line through gcfout Sensor arrays DCM as a network data hub Communicating with digitizers Configuring digitizers Data storage and retrieval Using miniSEED format Real-time data transmission CD1.0 and CD1.1 Troubleshooting DCM installations Cannot see the DCMs Web site over Http or Https Cannot connect to the DCMs Scream! serverCannot Gcfping the DCMs Scream! server Can Gcfping the DCMs Scream! server, but no data appears DCM is not receiving any data streamsUse the Serial port configuration → port name Web page, or DCM is receiving streams, but they do not contain any data143032 up 34 min, load average 1.24, 1.32 Configuration options GeneralDisk CMG-DCM Serial port configuration CMG-DCM Page Network configuration Ethernet portStatic routes DNS setup Incoming mail setup Outgoing mail setup Remote access Administrators PPP Mgetty Data transfer ScreamScream! Client AutoDRMHttp server Http clientCD1.0 CD1.1 CD1.1 subframe configuration DSS Server configuration Seed Page CMG-DCM Actions Data ViewerIcon bar Stream listDigitizer Setup General digitizer settings Digitizer output control CMG-DCM Trigger criteria CMG-DCM Tap # Rate Bandwidth Samples/s Auxiliary Mux channels Sensor mass control Check disk filesystem Disk toolsPartition, and format disk Flush flashDisk files CameraRecent Log Entries Network configuration SummaryDNS configuration Data Out Port, Serial Port A, Serial Port BFlash Status Tamper linesDisk Status Software Versions Inside the DCM File systems CMG-DCM Command line tools Configuration Digitizer console access Monitoring Data flowDigitizer status Tamper lines From the hard disk Updating the DCMOver the Internet Removing support packagesFirmware Libgconfigdb Port a and B Appendix a Connector pinoutsAppendix A.1 Modular DCM units Data OUT portUSB connector Network connectorAppendix A.2 Integrated DCM units DM/AM module outputAppendix B Sensor and digitizer types Appendix B.1 Sensor response codesAppendix B.2 Digitizer type codes Digitizer