Minicom Advanced Systems CMG-DCM manual Outgoing mail setup

Page 50

CMG-DCM

Outgoing mail setup

This page enables you to send mail from the DCM using the SMTP protocol. Both authenticated (i.e. sending a username to the server) and unauthenticated SMTP are supported, as is encryption using TLS (transport-layer security.) If you do not need the DCM to be able to send mail, select None from the net.mail.out.type drop-down menu and ignore the remaining settings.

net.mail.out.authsmtp : Select yes and give a username and password in the fields below to use authenticated SMTP for outgoing mail.

net.mail.out.password : The password needed to log in to the outgoing mail server, if using authenticated SMTP.

net.mail.out.server : The hostname or IP address of the outgoing mail server.

net.mail.out.tls : Select yes to encrypt the outgoing mail channel with TLS, no to leave communications unencrypted.

net.mail.out.type : Select smtp to use that protocol to send mail to the server. Currently only SMTP is supported. If you do not need the DCM to be able to send mail, select None.

net.mail.out.username : The username needed to log in to the outgoing mail server, if using authenticated SMTP.

50

Issue A

Image 50

Contents CMG-DCM Table of Contents December Inside the DCM Introduction CMG-DCM Inside the DCM Serial port services Network servicesSee .4, Connecting to a local network for full details Overview Installing the CMG-DCMPower supply Connecting to a single computer Connecting over a serial linkConnecting over Ethernet 192.168.0.xUsing an internal modem Connecting over USBConnecting to a local network Gcfgdbset option-namenew-value Wi-Fi Connecting to the InternetConnecting digitizers and external hardware Setting up the CMG-DCMWeb setup Setting up digitizers Using Scream DCM as a data store UsageGeneral notes Gnblocks port-number Page CMG-DCM DCM as a GCF data source Accessing the DCM command line through gcfout Sensor arrays DCM as a network data hub Communicating with digitizers Configuring digitizers Data storage and retrieval Using miniSEED format Real-time data transmission CD1.0 and CD1.1 Troubleshooting DCM installations Cannot Gcfping the DCMs Scream! server Cannot see the DCMs Web site over Http or HttpsCannot connect to the DCMs Scream! server Can Gcfping the DCMs Scream! server, but no data appears DCM is not receiving any data streamsUse the Serial port configuration → port name Web page, or DCM is receiving streams, but they do not contain any data143032 up 34 min, load average 1.24, 1.32 Configuration options GeneralDisk CMG-DCM Serial port configuration CMG-DCM Page Network configuration Ethernet portStatic routes DNS setup Incoming mail setup Outgoing mail setup Remote access Administrators PPP Mgetty Data transfer ScreamScream! Client AutoDRMCD1.0 Http serverHttp client CD1.1 CD1.1 subframe configuration DSS Server configuration Seed Page CMG-DCM Actions Data ViewerIcon bar Stream listDigitizer Setup General digitizer settings Digitizer output control CMG-DCM Trigger criteria CMG-DCM Tap # Rate Bandwidth Samples/s Auxiliary Mux channels Sensor mass control Check disk filesystem Disk toolsPartition, and format disk Flush flashRecent Log Entries Disk filesCamera Network configuration SummaryDNS configuration Data Out Port, Serial Port A, Serial Port BDisk Status Flash StatusTamper lines Software Versions Inside the DCM File systems CMG-DCM Command line tools Configuration Digitizer console access Monitoring Data flowDigitizer status Tamper lines From the hard disk Updating the DCMOver the Internet Removing support packagesFirmware Libgconfigdb Port a and B Appendix a Connector pinoutsAppendix A.1 Modular DCM units Data OUT portUSB connector Network connectorAppendix A.2 Integrated DCM units DM/AM module outputAppendix B Sensor and digitizer types Appendix B.1 Sensor response codesAppendix B.2 Digitizer type codes Digitizer