Minicom Advanced Systems CMG-DCM manual DCM as a network data hub

Page 28

CMG-DCM

3.4 The DCM as a network data hub

The most flexible way to operate the DCM is as a fully independent machine on your local area network. To do this:

1.Connect Gü ralp digitizers to PORT A and PORT B as necessary, using the serial data cable provided.

2.If you are using the DCM's USB capabilities, connect your external hardware or computer to the USB socket.

Note: USB distinguishes between hosts and clients. The DCM can act as either, depending on the options you specified at manufacture. If your DCM is a host, you can attach external USB peripherals such as hard disks. If it is a client, you can attach it to a computer, and it will appear as a network interface.

3.Connect a Gü ralp combined serial/power cable to the DATA OUT port. Make up a connector if necessary, and attach the power lines to a 12 V DC power supply.

4.Connect the 9-pin serial socket to a computer for configuration.

5.Connect an Ethernet cable to the NETWORK socket, and set up the network as described in Section 2.4, “Connecting to a local network”.

You should now be able to connect to the DCM's Web setup interface by typing its IP address into any browser, e.g.

https://192.168.0.2/

28

Issue A

Image 28
Contents CMG-DCM Table of Contents December Inside the DCM Introduction CMG-DCM Inside the DCM Serial port services Network servicesSee .4, Connecting to a local network for full details Power supply Installing the CMG-DCMOverview Connecting to a single computer Connecting over a serial linkConnecting over Ethernet 192.168.0.xUsing an internal modem Connecting over USBConnecting to a local network Gcfgdbset option-namenew-value Wi-Fi Connecting to the InternetConnecting digitizers and external hardware Setting up the CMG-DCMWeb setup Setting up digitizers Using Scream General notes UsageDCM as a data store Gnblocks port-number Page CMG-DCM DCM as a GCF data source Accessing the DCM command line through gcfout Sensor arrays DCM as a network data hub Communicating with digitizers Configuring digitizers Data storage and retrieval Using miniSEED format Real-time data transmission CD1.0 and CD1.1 Troubleshooting DCM installations Cannot connect to the DCMs Scream! server Cannot see the DCMs Web site over Http or HttpsCannot Gcfping the DCMs Scream! server Can Gcfping the DCMs Scream! server, but no data appears DCM is not receiving any data streamsUse the Serial port configuration → port name Web page, or DCM is receiving streams, but they do not contain any data143032 up 34 min, load average 1.24, 1.32 Configuration options GeneralDisk CMG-DCM Serial port configuration CMG-DCM Page Network configuration Ethernet portStatic routes DNS setup Incoming mail setup Outgoing mail setup Remote access Administrators PPP Mgetty Data transfer ScreamScream! Client AutoDRMHttp client Http serverCD1.0 CD1.1 CD1.1 subframe configuration DSS Server configuration Seed Page CMG-DCM Actions Data ViewerIcon bar Stream listDigitizer Setup General digitizer settings Digitizer output control CMG-DCM Trigger criteria CMG-DCM Tap # Rate Bandwidth Samples/s Auxiliary Mux channels Sensor mass control Disk tools Partition, and format diskCheck disk filesystem Flush flashCamera Disk filesRecent Log Entries Network configuration SummaryDNS configuration Data Out Port, Serial Port A, Serial Port BTamper lines Flash StatusDisk Status Software Versions Inside the DCM File systems CMG-DCM Command line tools Configuration Digitizer console access Monitoring Data flowDigitizer status Tamper lines Updating the DCM Over the InternetFrom the hard disk Removing support packagesFirmware Libgconfigdb Appendix a Connector pinouts Appendix A.1 Modular DCM unitsPort a and B Data OUT portUSB connector Network connectorAppendix A.2 Integrated DCM units DM/AM module outputAppendix B Sensor and digitizer types Appendix B.1 Sensor response codesAppendix B.2 Digitizer type codes Digitizer