Marmitek CM15PRO Lamp Module LM12 sold separately, Appliance Module AM12 sold separately, Timers

Page 8

respond to the setting of the physical Appliance Module that you will install (sold sepa- rately).

Make sure the Address Dials on the face of the Modules are set correctly. The red dial should be set to A on both Modules. The black dial on the Lamp Module should be set to 1 and the black dial on the Appliance Module should be set to a 2. If they are not set correctly, you can reset the dials with a small screw-driv- er (anything small enough to fit the slot in the dials).

LAMP MODULE LM12 (sold separately)

To control a lamp using AHP, follow these steps.

Please read through these installation steps completely before you start to install a Lamp Module.

1.Select a nearby lamp, one that uses a standard light bulb, and make sure its on/off switch is switched on.

2.Unplug the lamp from the wall outlet and plug it into the Lamp Module.

3.Plug the Lamp Module into a nearby AC outlet. If this outlet is controlled by a wall switch, make sure the wall switch is turned on.

4.If you have not already done so, start your AHP software by double clicking on the AHP icon.

5.Using your mouse, click the switch of "My Lamp Module" as shown on your com- puter screen. There may be a delay of one or two seconds from the time you click the "on screen" module switch and when the light actually turns on. You can also dim the lamp by moving the slide switch up and down.

APPLIANCE MODULE AM12 (sold separately)

Controlling an appliance is just as easy!

Please read through these installation steps completely before you start to install an Appliance Module.

1.Select a small appliance, such as an AC powered radio, and make sure its on/off switch is switched on.

2.Unplug the appliance from the wall outlet and plug it into the Appliance Module.

3.Plug the Appliance Module into a nearby AC outlet. If this outlet is controlled by a wall switch, make sure the wall switch is turned on.

4.If your AHP software is not running, start it by double clicking on the AHP icon.

5.Using your mouse, click the switch of "My Appliance" as shown on your computer screen. There may be a delay of one or two seconds from the time you click the "on screen" module switch and when the appliance actually turns on.

Timers

You can schedule each of your Modules to turn on or off any time by clicking on the small clock at bottom left hand side of your "on screen" modules. If you have trouble

8

© MARMITEK

Image 8
Contents CM15ProCM15Pro Marmitek CM15Pro + ActiveHome Pro Safety WarningsHOW does Marmitek X-10 WORK? Known devices which can cause attenuation are Signal RangeAdresses Introduction System Requirements ContentsHardware Setup and Software Installation Using Marmitek ActiveHomePro OperationAppliance Module AM12 sold separately TimersLamp Module LM12 sold separately Save changes in the CM15Pro Frequently Asked QuestionsMacros How many lights and appliances can I control using X-10? My modules will not respond to my controllerTechnical Specifications Marmitek Sicherheitshinweise WIE Funktioniert Marmitek X-10?Reichweite VON Signalen AdressierungGebrauchsanleitung Einführung Wir empfehlen um folgende Geräte zu kontrollierenSystemanforderungen Hardware Setup UND Software InstallationVerpackungsinhalt CM15Pro + ActiveHome Pro Lampenmodul LM12 wird separat geliefert BedienungDie Anwendung der Marmitek ActiveHomePro Timer Zeitpläne UND Makros Befehlgruppen TimerfunktionGerätemodul AM12 wird separat geliefert MakrofunktionHäufig Gestellte Fragen Änderungen im CM15Pro speichernWie kommt es, dass manche Module spontan ein- oder ausgehen? Meine Module reagieren nicht auf meinen ControllerTechnische Daten Avertissements DE Securite Comment Fonctionne LE Système Marmitek X-10?Porté DES Signaux Guide Utilisateur Introduction Produits pouvant créer une atténuationExigences DU Système Installation DU Matériel ET DU LogicielContenu DE L’EMBALLAGE Utilisation ’utilisation de Marmitek ActiveHomeProModule DE Lampe LM12 livré séparément Timers Horaires ET Macros Groupes DE Commandes Fonction TimerFonction Macro Mémoriser les changements dans CM15ProFoire AUX Questions Mes modules ne réagissent pas avec mon contrôleurCaractéristiques Techniques Marmitek Avisos DE Seguridad ¿CÓMO Funciona EL X-10 DE MARMITEK?Ajuste DE Direcciones Alcance DE LAS SeñalesAparatos a controlar Breve Manual DE Instrucciones Contenido DEL EmbalajeExigencias DEL Sistema IntroducciónHardware Setup E Instalacion DEL Software Modulo DE Lampara LM12 se entrega separadamente ManejoEl manejo de ActiveHomePro de Marmitek Función Macro Timers Esquemas DE Tiempo Y Macros Grupos DE ComandosFunción Timer Preguntas Frecuentes Guardar modificaciones en la CM15ProDatos Technicos Mis módulos no reaccionan a mi controladorOrdenadores, pantallas, etc Precauzioni DI Sicurezza Come Funziona Marmitek X-10?Indirizzi Portata DEI SegnaliGuida Rapida ALL’INSTALLAZIONE IntroduzioneRequisiti DEL Sistema Disposizione DELL’HARDWARE E Installazione DEL SOFT- WareContenuto Dellimballaggio Comando ’uso del ActiveHomePro di MarmitekModulo PER Lampade LM12 è fornito separatamente Funzione macro Timer Orari E Macro Gruppi DI ComandiFunzione timer Domande Frequenti Salvare le modificazioni nel CM15ProDati Tecnici Miei moduli non reagiscono al controllerCome computer, videoterminali, ecc Veiligheidswaarschuwingen HOE Werkt Marmitek X-10?Bereik VAN Signalen AdresseringGebruiksaanwijzing Introductie Systeemvereisten Hardware Setup EN Software InstallatieInhoud VAN DE Verpakking Bediening Het gebruik van Marmitek ActiveHomeProLamp Module LM12 wordt apart geleverd Timers TIJDSCHEMA’S EN MACRO’S Groepen VAN COMMANDO’S Timer functieApparaat Module AM12 wordt apart geleverd Macro functieVeel Gestelde Vragen Wijzigingen opslaan in de CM15ProHoeveel lamp en schakelmodules kan ik bedienen met X-10? Hoe komt het dat sommige Modules spontaan aan- of uitgaan?Technische Gegevens Mijn modules reageren niet op mijn controllerGewicht Gram Afmetingen bxhxd in mm 66,7 x 113,5 x 45,3 Declaration of Conformity
Related manuals
Manual 2 pages 6.29 Kb