Lantronix 1-T2, MSS100 manual Multihost Mode

Page 44

Multihost Mode

Using the MSS

In UDP mode, each MSS would have to be conÞgured to both send packets to and accept packets from the other MSS. The conÞguration is as follows:

mss_a

Local>> CHANGE DEDICATED TCP

 

192.168.5.10:4096U

 

Local>> CHANGE AUTOSTART ENABLED

 

Local>> CHANGE ACCESS DYNAMIC

mss_b

Local>> CHANGE DEDICATED TCP

 

192.168.5.2:4096U

 

Local>> CHANGE AUTOSTART ENABLED

 

Local>> CHANGE ACCESS DYNAMIC

Setting up Dedicated hosts ensures that the units will always talk to each other. Enabling Autostart for both units enables one MSS to send data to the other MSS without having to wait for a serial carriage return to start the session. Finally, when Autostart is enabled, the access mode must be either Local or Dynamic (more ßexible).

NOTE: Autostart can be disabled if you want the MSS to wait for a carriage return before sending data. Also, the Autostart character can be changed, if desired, using the Change Autostart command.

5.4 Multihost Mode

Multihost mode is used to set up a data pipe between a serial device attached to the MSS and multiple hosts on the network. Data from any network host goes out of the MSS serial port, and data from the serial port is sent to all connected network hosts.

The MSS attempts to send data in the order it is received. That is, it reads in and sends data from one host before reading in any data from another host. The MSS will not packetize or perform conversions, nor will it change the data to show which host(s) it came from; the host(s) and serial device handle this independent of the MSS.

NOTE: The MSS hardware automatically turns off the transmitter after the last character goes out. The latency is within 1.5 character times.

5 - 12

Image 44
Contents Serial Server Installation Guide Part Number Contents Contact Information Troubleshooting Pinouts Iii Page Introduction Terms ProtocolsSoftware ConfigurationConfiguration Introduction Installation MSS ComponentsInstallation MSS LEDsInstallation Power-up Diagnostics Is It Working? 4Pinging the MSSPage Getting Started IP Address Configuration Using EZWebConUsing an ARP Entry and the Ping Command 1Entering ARP and Ping Unix Using a DHCP, BOOTP, or Rarp Reply Using the Serial ConsoleEZWebCon Login and Configuration Incoming LoginsControlling Incoming Logins Serial Port Logins Other Incoming TCP/IP LoginsIncoming LAT Logins RloginTelnet Remote Console LoginsStarting Outbound Connections 3 LAT Logout2 SPX Command Set System PasswordsPrivileged Password Basic Configuration1 TCP/IP Parameters Login PasswordProtocol Configuration 2 IPX/SPX Parameters Serial Port Configuration LAT ParametersBasic Configuration Serial Port Configuration Change Preferred SPX None Otherwise, only Telnet console port connections are possible Page Socket Connections Using the MSSIncoming Connections 1.2 IPX/SPX Socket Connections LAT Connections1.1 TCP/IP Socket Connections Host Applications 4Reducing Flow ControlLocal Switch Interactive ConnectionsCode Examples Session ControlBackward and Forward Switches 8DeÞning SwitchesSession Limits Outgoing ConnectionsDisconnect and Resume 10Connecting with Rlogin 2.3 SPX12Connecting to a Service 2.4 LATStatus Displays Show Server Characteristics Show ServicesShow Server Counters Show SessionsEmulating a Direct Serial Connection MssbMultihost Mode 1 Configuring Multihost Mode 15Setting the MSS for Multihost ModeMultihost Mode Using the MSS Contact Information LANtronix Troubleshooting Problems and Error MessagesTable B-1Problems and Error Messages, Bootp Troubleshooting Etc/services Þle?Tftp Troubleshooting Entering Commands at the Boot PromptFigure B-1BCP Command Examples Entering Commands at the Boot Prompt Troubleshooting Modem Configuration Checklist Page Pinouts DB25 ConnectorRJ-45 Connector DTR Data Terminal Ready Modem WiringDSR Data Signal Ready versus CD Carrier Detect Via FTP Updating SoftwareObtaining New Software Via a Modem Figure D-1Lantronix FTP SessionReloading MSS Software Updating Software Reloading MSS SoftwareFigure D-3Reloading Flash ROM using NetWare NetWare2 TCP/IP 3 MOPTroubleshooting Flash ROM Updates TftpPower Specifications Temperature LimitationsSpecifications Relative Humidity LimitationsPage Warranty Statement Declaration of Conformity EMCIndex Index-iLoadhost 4-3, 5-9, B-6 Index-iiTelnet 1-4, 5-1 Index-iii