Lantronix manual Serial Interface, Front of XPress DR+

Page 20

Chapter 3: Installation and Hardware

Figure 3-2. Front of XPress DR+

Serial Interface

The XPress DR+ supports RS-232 via RJ45 connectors. It also supports RS-422/485 via screw terminals (Serial Port 2 only).

Note: Serial Port 2 supports RS232, RS422, and RS485, but only one mode at a time. This means you can use either the RJ45 connector or the terminal block, not both.

The RJ45 serial connectors only support RS232, up to 230400 bits per second.

XPress DR+ User Guide

Image 20

Contents XPress DR+ User Guide Date Rev Comments Lantronix Corporate HeadquartersTechnical Support Sales Offices Contents Contents Using DeviceInstallerConfiguration Using Web Manager Setup Mode Channel Configuration Configuration Using Telnet or Serial Port Setup ModeSetup Mode Server Configuration Setup Mode Advanced Settings Expert Settings Option 5Firmware Upgrades Monitor ModeTroubleshooting and Technical Support Appendix D Binary to Hexadecimal Conversions 108Appendix F Warranty 115 Index 116 FiguresTables Using This Guide Purpose and AudienceSummary of Chapters Chapter DescriptionUsing This Guide Additional DocumentationIntroduction Product DescriptionIntroduction XPress DR+ FrontIndustrial Automation Protocols Network Protocols Serial TunnelingXPress DR+ Application Examples Example of Serial TunnelingAddresses and Port Numbers Hardware AddressIP Address Port Numbers Configuration Methods Lantronix Web Manager. See Configuration Using Web ManagerInstallation and Hardware Physically Connecting the XPress DR+Whats in the Box? What Must the User Provide?Installation and Hardware XPress DR+ Front PanelSerial Interface Front of XPress DR+Screw Terminal Serial Connectors RJ45 Serial Connector PinoutsSerial Screw Terminal Pinout for RS422 4-Wire Serial Screw Terminal Pinout for RS485 2-WirePin RS-232 to Serial RJ45 Cable P/N DTE, 9-Pin XPress DR+ Female Serial RJ45Ethernet Interface Ethernet Interface SignalsTypical RJ45 Connector Multi-Drop Ethernet Connections Power RequirementsReset Switch Ethernet Activity LED LEDsRXD Activity LED TXD Activity LED Ethernet Link LED XPress DR+ LED Functions DimensionsStatus Meaning Wall Mount Bracket Product Information LabelSerial Tunneling Network XPress DR+WApplication Examples XPress DR+W Ad Hoc NetworkSerial Tunneling Infrastructure Physically Connecting the XPress DR+W Ad Hoc XPress DR+W ConnectionTypical XPress DR+W Configuration Front Panel DescriptionRequired Information for Initial Configuration XPress DR+W LED FunctionsInstalling the XPress DR+W for Initial Configuration Server Configuration OptionWlan Settings IP Address Subnet Mask GatewayNetwork Mode XPress DR+W only BootP/DHCP/AutoIP optionsSet Gateway IP Address Options BitWlan Configuration Option Change Telnet Configuration PasswordNetmask Number of Bits for Host Part Change Dhcp Device NameAdhoc Network Channel TopologyNetwork Name Ssid Passphrase Key Type Encryption KeyHex WPA WPA2/802.11i Fixed or Automatic Data RateNext Steps Transmission Data RateUsing DeviceInstaller Installing DeviceInstallerTo install DeviceInstaller Assigning an IP AddressAccessing the XPress DR+ Using DeviceInstaller Viewing the Current ConfigurationUsing DeviceInstaller To view the units current settingsSetting Description Supports Configurable PinsSupports Http Setup Supports Dynamic IPConfiguration Using Web Manager Configuration Using Web ManagerAccessing XPress DR+ Using DeviceInstaller Network Configuration Lantronix Web ManagerAutomatic IP Address Configuration To assign an IP address automaticallyAutoIP Dhcp Host NameServer Configuration Static IP Address ConfigurationDefault Gateway To assign an IP address manuallyAdvanced Server ConfigurationTo configure the units device server settings 0x77FE Server Port MTU Size Host List ConfigurationTo configure the units host list Channel Configuration Serial SettingsRetry Settings To configure the channel’s serial settingsPort Settings ChannelFlush Output Buffer Network to Serial Pack ControlFlush Input Buffer Serial to Network Connection Settings TCP To configure a channel’s TCP settingsConnect Mode Passive Connection Connect Mode Active ConnectionEndpoint Configuration Connect ProtocolConnection Settings UDP Disconnect ModeTo configure a channel’s UDP settings Common OptionsDatagram Mode Datagram TypeWlan Configuration XPress DR+W only Device Address TableTo configure the XPress DR+W’s Wlan settings Wlan Settings Ad Hoc Network TypeWireless Network Configuration Network Name SsidNetwork Type ChannelWPA Options Wireless Network SecurityWEP Options Applying Settings Applying Factory DefaultsAdvanced Settings WPA2/802.11i OptionsConfiguration Using Telnet or Serial Port Setup Mode Accessing Setup ModeTo establish a Telnet connection Configuration Using Telnet or Serial Port Setup ModeSerial Port Connection Exiting Setup Mode To exit setup modeSetup Mode Server Configuration Setup Mode Server Configuration Dhcp Name Baudrate Setup Mode Channel ConfigurationChannel 1 Option 1 and Channel 2 Option Interface Mode Setup Mode Channel ConfigurationMode Option Common I/F Mode Setting Binary HexFlow Port NumberFlow Control Option Hex Port Numbers Reserved forConnect Mode Connect Mode OptionActive Startup Incoming ConnectionResponse Hostlist Autostart AutomaticConnection Modem Mode To enable the hostlistDatagram Type Directed UDPMessage Meaning Modem Mode Function Command Modem Mode CommandsRemote IP Address Send the Escape Sequence +++ in Modem ModeAuto Increment Source Port Disconnect Mode Option Disconnect Mode OptionsRemote Port DisConnModeOption Flush Mode Buffer FlushingPack Control DisConnTime Inactivity Timeout Packing IntervalTrailing Characters Send CharactersChannel Port Password Wlan Settings XPress DR+W OnlySend Characters Telnet Terminal TypeTopology 0=Infrastructure, 1=Adhoc 0 ? WEP WEP64 or 13 WEP128 bytes and limits the number of key TX Data rate 0=fixed, 1=auto fallback 1 ? Enable Power Management Setup Mode Advanced Settings Expert Settings OptionARP Cache timeout in seconds Disable Monitor Mode at bootupSecurity Settings Option Enable alternate MACSetup Mode Advanced Settings Http Port NumberDisable Snmp Disable Telnet SetupDisable Tftp Firmware Upgrade Disable Port 77FE HexDefault Settings Option Expert Settings Security SettingsWlan Settings XPress DR+W only Topology AdHoc Network NameFirmware Upgrades Using Tftp Graphical User InterfaceObtaining Firmware Reloading Firmware ROM FileTo recover firmware Using Tftp Command Line InterfaceFirmware Upgrades Firmware Upgrades Monitor Mode Entering Monitor Mode Using the Serial PortEntering Monitor Mode Using the Network Port Monitor Mode CommandsMonitor Mode Command Command Name FunctionMonitor Mode Commands G0, G1, ....,Ge, GfCommand Response Codes Response MeaningTroubleshooting and Technical Support Problems and Error MessagesProblem/Message Reason Solution Problems and Error MessagesTroubleshooting and Technical Support XPress DR+ User Guide 101 Technical Support Technical Support Europe, Middle East, and AfricaAppendix a Technical Specifications XPress DR+ and XPress DR+W SpecificationsCategory Ieee 802.11b/g Appendix a Technical SpecificationsXPress DR+W Wireless Specifications Applications Appendix B Lantronix Cables and AdaptersLantronix P/N Description Appendix C Alternative Methods of Assigning an IP Address AutoIPTo assign a temporary IP address ARP and TelnetAppendix C Alternative Methods of Assigning an IP Address Appendix D Binary to Hexadecimal Conversions Converting Binary to HexadecimalConversion Table Scientific CalculatorAppendix D Binary to Hexadecimal Conversions Appendix E Compliance Information Declaration of ConformityElectromagnetic Emissions and Immunity XPress DR+ Emissions ImmunityElectromagnetic Emissions and Immunity XPress DR+W Appendix E Compliance InformationRadio Canada Industry Canada Notice XPress DR+W Regulatory InformationUSA Federal Communications Commission FCC Notice Exposure of Humans to RF Fields Europe R&TTE Directive 99/5/EC, Wireless NoticeAntenna Notice Australia & New Zealand Wireless Notice Appendix F Warranty Index