Lantronix ETS32PR, ETS8PS, ETS16PS, ETS16PR manual Installation

Page 14

Installation

a)It runs through a set of power-up diagnostics for approximately 12 seconds. The LEDs show varying patterns corresponding to the tests being run.

b)It tries to obtain TCP/IP configuration information via DHCP, BOOTP, and RARP. This may take as long as 15 seconds if no hosts answer the requests. During this step, the OK LED blinks approximately 3 times per second and the NET LED blinks occasionally.

7.Install EZWebCon on your 32-bit Windows PC computer. The EZWebCon software is located on the distribution CD-ROM. Alternatively, download it from ftp://ftp.lantronix.com.

14	ETS Installation Guide

Image 14

Contents ETS Installation Guide Sales Offices Lantronix Corporate HeadquartersTechnical Support Disclaimer and Revisions Contents LAT Configuration Specifications ContentsRS-232 IntroductionSupported Serial Protocols RS-423How to Use This Manual IntroductionEtsps Front Panels InstallationEtsp Product Descriptions ETS8PS/ETS16PS LEDsETS16PS Back Panel Installing the EtspInstallation Etspr Product Descriptions ETS16PR Front PanelEtspr LEDs Installing the EtsprETS32PR Front Panel Sample Etspr Network Layout ETS16PR shown Installation Getting Started Configuration MethodsUsing a Web Browser Etspr models EZWebConUsing EZWebCon TCP/IP ConfigurationIncoming Logins Console TerminalUsing a Directed Ping Packet ARP and Ping on UnixUsing the Command Line Interface Was the Installation Successful?Using a BOOTP, DHCP, or Rarp Reply Using the ETS Console Server ExampleUsing the ETS Define the MenusEnable Menu Mode Configure SwitchesUsing Menus 10. Configuring SwitchesTCP Configuration Serial Tunnel ExampleComm Port Redirector UDP ConfigurationMulti-port Serial Tunnel Configuration LPR Printing ServicesPrinting on the ETS LPR on Windows 2000, XP,To enable LPR support, install Print Services for Unix Printing on the ETSPrinting on the ETS Printing on the ETS Local Define Service ETSHPLaserjet port Enable LPR on Windows NT 3.5.1 and later Printing on the ETS LPR on Windows 95/98 LPR on Unix HostsLPR on AIX Hosts Adding /etc/hosts EntryLPR on HP Hosts LPR on SCO Unix HostsRtel Functionality Answer the questions that followUnix Host Troubleshooting Area to Check ExplanationNdps Printing NDS Print Queues NetWare ConfigurationConfigure your ETS Obtain an NDS LicenseFrom the Menu Bar, select Tools Print Services Quick Setup NetWare Administrator Quick Setup Print QueuesNetWare Configuration Pconsole Print QueuesNetWare Host Troubleshooting Use the Show Protocols NetWare AccessCode Meaning Remedy NetWare Configuration Printing Directly to a Port LAT ConfigurationLAT Host Troubleshooting LAT Configuration Translating LAT Error CodesBitronics AppleTalk ConfigurationMacintosh Services AppleTalk ZonesAppleTalk Host Troubleshooting AppleTalk ConfigurationETS Configuration DLC Configuration for LAN ManagerDLC Configuration Host ConfigurationContact Information Technical Support Europe, Middle East, and AfricaTroubleshooting Power-up TroubleshootingTroubleshooting Dhcp TroubleshootingBootp Troubleshooting Rarp Troubleshooting Entering Commands at the Boot PromptFlush NVR SET Bootp Enabled, DisabledSET Dhcp Enabled, Disabled FlashSET Software filename Troubleshooting SET Rarp Enabled, DisabledSET Secondary ipaddress Show ServerPinouts Ethernet ConnectorRJ45 Serial Connectors RJ45 to DB25Pinouts Figure C-3. Pinouts of RJ45-DB25 ConnectionsFigure C-5. Wire Splicer RJ45 to DB9Obtaining Software Updating SoftwareChoosing the Right Software File Via the Web Via FTPUpdating Software Reloading SoftwareReloading Sequence NetWare MOPTroubleshooting Flash ROM Updates TftpEnvironmental Limitations SpecificationsPower Information Conventions Frequently-Used CommandsServer Commands Frequently-Used Commands NopasswordBanner Port Commands Zero Counters ALLProtocol Commands SHOW/MONITOR PortNetware Etherii Compliance and Warranty Information Declaration of ConformityWarranty Compliance and Warranty Information