Lantronix ETS32PR, ETS8PS, ETS16PS, ETS16PR manual LPR on HP Hosts, LPR on SCO Unix Hosts

Page 34

Printing on the ETS

4.From the dialog box that appears, choose remote.

5.From the next dialog box, choose Remote Printing.

6.The Add a Standard Remote Print Queue dialog box will appear. Enter the following information.

‹The name of the print queue,

‹The name of the ETS unit,

‹The name of the ETS service,

‹The type of print spooler on the remote server, and

‹A description of the printer on the remote server.

7.A dialog box will appear: “Added print queue ets_prt”. Click Done.

Note: If you are unable to use SMIT, see the Device Server Reference Manual on the CD-ROM for UNIX commands used to set up print queues.

8. Print to the queue using normal lp syntax.

Figure 5-5. Printing to Queue

% lp -dets_prt filename

LPR on HP Hosts

The System Administration Manager (SAM) allows you to create print queues.

Note: If you are unable to use SAM, the Device Server Reference Manual located on the CD-ROM describes UNIX commands that can be used to set up print queues.

To create a print queue:

1.At the HP prompt, type sam.

2.From the main application window, choose Printers and Plotters.

3.In the Printers and Plotters window, choose Printers/Plotters.

4.In the pull-down menu, select Remote Printer/Plotter from the Actions menu.

5.The Add Remote Printer window will appear. SAM will prompt you for:

‹The printer name (the name of the print queue),

‹The remote system name (the ETS name),

‹The remote printer name (the ETS service),

‹The remote cancel model, and

‹The remote status model.

LPR on SCO UNIX Hosts

LPR is supported in SCO V3.2 release 4 with TCP/IP Version 1.2 and greater.

To configure a print queue using LPR, issue the mkdev rlp command. This will install the Berkeley remote printing files and executable programs.

Note: The mkdev rlp command should only be issued once, or serious problems will occur. If this happens, contact SCO technical support.

You can print to this queue using normal lp syntax once the remote printer is set up. To create a remote printer:

1. Issue the rlpconf command.

34

ETS Installation Guide

Image 34
Contents ETS Installation Guide Technical Support Lantronix Corporate HeadquartersSales Offices Disclaimer and Revisions Contents LAT Configuration Specifications ContentsRS-232 IntroductionSupported Serial Protocols RS-423How to Use This Manual IntroductionEtsps Front Panels InstallationEtsp Product Descriptions ETS8PS/ETS16PS LEDsInstallation Installing the EtspETS16PS Back Panel Etspr Product Descriptions ETS16PR Front PanelETS32PR Front Panel Installing the EtsprEtspr LEDs Sample Etspr Network Layout ETS16PR shown Installation Getting Started Configuration MethodsUsing a Web Browser Etspr models EZWebConUsing EZWebCon TCP/IP ConfigurationIncoming Logins Console TerminalUsing a Directed Ping Packet ARP and Ping on UnixUsing a BOOTP, DHCP, or Rarp Reply Was the Installation Successful?Using the Command Line Interface Using the ETS Console Server ExampleUsing the ETS Define the MenusEnable Menu Mode Configure SwitchesUsing Menus 10. Configuring SwitchesTCP Configuration Serial Tunnel ExampleMulti-port Serial Tunnel Configuration UDP ConfigurationComm Port Redirector LPR Printing ServicesPrinting on the ETS LPR on Windows 2000, XP,To enable LPR support, install Print Services for Unix Printing on the ETSPrinting on the ETS Printing on the ETS Local Define Service ETSHPLaserjet port Enable LPR on Windows NT 3.5.1 and later Printing on the ETS LPR on Windows 95/98 LPR on Unix HostsLPR on AIX Hosts Adding /etc/hosts EntryLPR on HP Hosts LPR on SCO Unix HostsRtel Functionality Answer the questions that followUnix Host Troubleshooting Area to Check ExplanationNdps Printing NDS Print Queues NetWare ConfigurationConfigure your ETS Obtain an NDS LicenseFrom the Menu Bar, select Tools Print Services Quick Setup NetWare Administrator Quick Setup Print QueuesNetWare Configuration Pconsole Print QueuesNetWare Host Troubleshooting Use the Show Protocols NetWare AccessCode Meaning Remedy NetWare Configuration LAT Host Troubleshooting LAT ConfigurationPrinting Directly to a Port LAT Configuration Translating LAT Error CodesBitronics AppleTalk ConfigurationMacintosh Services AppleTalk ZonesAppleTalk Host Troubleshooting AppleTalk ConfigurationETS Configuration DLC Configuration for LAN ManagerDLC Configuration Host ConfigurationContact Information Technical Support Europe, Middle East, and AfricaTroubleshooting Power-up TroubleshootingBootp Troubleshooting Dhcp TroubleshootingTroubleshooting Rarp Troubleshooting Entering Commands at the Boot PromptFlush NVR SET Bootp Enabled, DisabledSET Dhcp Enabled, Disabled FlashSET Software filename Troubleshooting SET Rarp Enabled, DisabledSET Secondary ipaddress Show ServerPinouts Ethernet ConnectorRJ45 Serial Connectors RJ45 to DB25Pinouts Figure C-3. Pinouts of RJ45-DB25 ConnectionsFigure C-5. Wire Splicer RJ45 to DB9Obtaining Software Updating SoftwareChoosing the Right Software File Via the Web Via FTPReloading Sequence Reloading SoftwareUpdating Software NetWare MOPTroubleshooting Flash ROM Updates TftpPower Information SpecificationsEnvironmental Limitations Server Commands Frequently-Used CommandsConventions Frequently-Used Commands NopasswordBanner Port Commands Zero Counters ALLProtocol Commands SHOW/MONITOR PortNetware Etherii Compliance and Warranty Information Declaration of ConformityWarranty Compliance and Warranty Information